Genuine Land Rover Parts

Sunroof Handle Assembly operates the manually-operated glass sunroof, forming the interface between the occupant and the roof panel's opening mecha...

Side Window Filler Strip for the rear side window assembly. The filler strip closes the gap along the side window channel, completing the seal and...

Spring Nut A clip-on spring-steel fastener, also known as a speed nut, used across body, grille and chassis fittings. It slides over a panel edge ...

Bulb & Holder - Main Instrument Panel for the Discovery 2 instrument cluster illumination circuit. This bulb and holder assembly fits into the...

Splash Seal

Upper Front Suspension Arm Ball Joint The upper ball joint forms the top pivot between the front upper suspension arm and the wheel knuckle, holdi...

Primary Fuel Filter for the diesel fuel supply system of the 2.0L I4 diesel (AJ200 / AJ20D4 / AJ21D4) engine. The primary filter separates water a...

Air Duct - the induction duct of the air cleaner assembly, carrying filtered air from the air cleaner outlet to the turbocharger compressor inlet. ...

Oil Cooler Gasket for the AJ-Series V8 petrol engine, sealing the oil cooler and filter housing to the cylinder block. This gasket forms the oil-t...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Wiper Blade for the rear window wiper assembly of the New Defender (L663). This blade uses the Aquablade design: washer fluid is channelled throug...

Wiper Blade for the front windscreen wiper assembly of the New Defender (L663, 2020 onwards). Fits the front wiper system on the Defender 90, Defe...

Wiper Blades - Front Pair is a replacement windscreen wiper blade set, supplied as a matched front pair for right-hand drive configurations. The bl...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Washer Fluid Level Sensor for the windscreen washer system. The sensor fits into the washer fluid reservoir and monitors the volume of fluid remai...

Upper Radiator Hose for the engine cooling circuit on the 2.0L Ti VCT petrol engine. This upper radiator hose carries engine coolant from the engi...

Oil Filter Gasket Kit for the engine oil filtration circuit of the 2.0L Ingenium (AJ200) engine, renewed with the oil filter element at each servic...

Coolant Outlet Connection is part of the engine cooling circuit, forming the sealed outlet junction where coolant leaves the engine on its way to t...

Hose - Filler Pipe

Strap - Fuel Tank

Gear Lever Boot - a flexible gaiter that seals around the base of the gear-change lever where it passes through the transmission tunnel. It closes...

Mudflap

Mudflap

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...

Wiper Arm is the windscreen wiper arm that carries the wiper blade across the windscreen. It mounts to the wiper linkage spindle and transfers the...

Coolant Hose forms part of the heater line within the engine cooling system, routing coolant between the engine and the heater matrix. Supplied co...

Water Outlet Connection (Upper) for the 4.4L DOHC V8 turbo-diesel (TDV8) engine. Part of the thermostat and coolant housing assembly, it carries co...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Rear Coil Spring Insulator seats between the rear coil spring and its mounting seat within the rear suspension assembly. It cushions the spring ag...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Seat Belt

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Tube - Water Outlet

Front Bumper End Cap - Outer, installed at the outer section of the front bumper assembly. This component forms part of the Front Bumper & Bum...

Locking Nut is a threaded fastener with a prevailing-torque locking feature that resists loosening under vibration.

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Rear Door Outer Waist Seal - Right-Hand fitted along the upper edge of the right-hand rear side door outer panel, sealing the interface between the...

Rear Door Outer Waist Seal - Left-Hand fitted along the upper edge of the left-hand rear side door outer panel, sealing the interface between the o...

Timing Gear Bolt is the hex-head flanged bolt that retains the upper timing gear on the valve-timing drive. It secures the upper gear against the ...

Oil Cooler Gasket for the oil cooler / oil filter housing assembly on the 2.7L TDV6 diesel engine. The gasket seals the joint between the oil cool...

Cylinder Head Bolt for the cylinder head assembly on TDV6 and TDV8 diesel engines. The bolt secures the cylinder head to the engine block, clamping...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Front Cover Gasket for the LT85 five-speed manual gearbox, G20C unit. This gasket seals the front cover to the main gearbox casing, preventing oil...

Spire Nut, a J-type sheet-metal spring nut (also known as a speed nut) used to secure trim, panels and fittings. The nut clips over a panel edge o...

Tailgate Cable Stud is the anchor point for the rear tailgate support cable. Mounted on the rear body, the stud receives the end of the tailgate c...