Land Rover Axle & Swivel Parts

Stub Axle Bolt Fixing bolt that secures the stub axle to the axle case. Clamps the stub axle onto the axle housing as part of the hub and stub axl...

Drive Flange is a torque-transmitting flange fitted to the manual gearbox output. It provides the bolted coupling that carries drive from the gear...

Stub axle kit Def from LA front

Swivel Pin Housing Kit rebuilds the upper pivot of the front axle swivel housing, where the steering knuckle articulates on the axle. This is the v...

Half Shaft Shim - 0.90mm is a 0.90mm selective shim that fits on the outside of the axle driving member to set the endfloat of the half shaft withi...

Half Shaft Shim - 0.60mm is a 0.60mm selective shim used to set the endfloat of the axle half shaft within the hub assembly. It is fitted at the d...

Front Axle Shim, 0.45mm thick. Fitted to the front axle half-shaft assembly to set the correct end-float, taking up clearance so the shaft is posit...

Lower Swivel Pin forming the lower pivot of the front axle swivel housing. The pin bolts to the underside of the swivel pin housing and carries th...

thrust collar, bush for stub axle - RRclassic upto (VIN) HA610293, - 101" Forward Control.

Axle Buffer - the progressive rubber bump stop that limits suspension travel at full compression. Mounted between the axle and chassis, it absorbs...

Door Glass Regulator Shim - a packing shim used at the door window regulator and glass channel. It sets the regulator and channel at the correct st...

Body Mounting Shim used to set the correct clearance and alignment between the body tub and the chassis mounting points. This thin flat shim is us...

Half Shaft for the axle drive assembly, transmitting drive torque from the differential to the wheel hub. Splined to the differential side gear at ...

Front Axle Shaft - left-hand - for the Defender with early-type 23-spline CV joint. This drive shaft transmits torque from the front differential ...

Stub Axle - Front

Stub axle

Swivel Pin is the upper pin of the front axle swivel assembly. It bolts to the top of the swivel housing and carries the upper bearing about which ...

Trunnion

Swivel Bearing - the bearing on which the front axle swivel pin housing pivots, within the steering swivel assembly. It locates the swivel pin in ...

Axle Oil Level Plug - Plastic is the filler and level plug for the front and rear differential housings. This plug seals the oil level/filler aper...

Outer Shim - 1.35mm - Front Halfshaft / CV Joint This 1.35mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Half Shaft Shim is a 1.05mm selective shim used in the front axle drive shaft and hub assembly. It sets the endfloat of the front half shaft drive...

Front Half Shaft for the right-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant vel...

Half Shaft is the left-hand rear axle half shaft. Operating within the rear axle assembly, it transmits drive torque from the rear differential to...

Rear Half Shaft - right-hand - for the Defender with early-type 23-spline CV joint. This solid steel drive shaft transfers torque from the rear di...

Upper Front Swivel Pin for the front axle swivel housing assembly. The upper swivel pin bolts to the top of the swivel housing and forms the upper...

Rear Stub Axle for the Salisbury rear axle assembly. The stub axle bolts to the outer end of the axle casing and forms the fixed spindle on which ...

Axle Flange Kit for the pinion drive flange of the Salisbury rear differential. The flange transmits drive from the differential pinion to the rea...

Front flange LT230

Swivel Ball Taper Plug for the front axle swivel housing. This tapered-thread plug screws into a port in the swivel ball housing, sealing it agains...

Swivel Pin Bush - Upper is the upper pivot bush in the front axle swivel housing assembly. It seats in the top of the swivel housing and locates t...

Rear Axle Breather Pipe vents the rear axle casing. It equalises internal air pressure as the axle heats and cools, allowing the casing to breathe...

Rear Axle Outer Stub Shaft is part of the rear axle and hub assembly on the left-hand (LH) side. It transmits drive from the rear halfshaft to the...

Swivel Housing Gaiter Kit - Leather - Pair for the front axle swivel housing assembly on the Defender 90 and 110. The swivel housing gaiter seals ...

Rear Stub Axle for non-ABS applications. Bolts to the rear axle case to carry the hub bearings and support the rear hub assembly. For vehicles bui...

Half Shaft Shim is a 1.50mm selective shim used in the axle drive shaft and hub assembly. It sets the endfloat of the half shaft drive member with...

Front Half Shaft for the left-hand side of the front axle. This axle shaft transmits drive from the front differential outward to the constant velo...

Differential Pinion Bearing Shim - 0.064 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Shaft 90/110 RH 31/10

Rear Axle Half Shaft - right-hand, 10/24 spline, for the Series III rear axle. This shaft transmits drive from the rear differential to the rear wh...

Rear Axle Stub for the rear axle assembly on early Series Land Rovers. The axle stub is the outboard section of the rear axle shaft assembly, carr...

Rear Halfshaft for the E.N.V. heavy-duty rear axle, left-hand side. The halfshaft transmits drive from the differential through the axle casing to...

Rear Halfshaft for the rear axle hub and driveshaft assembly, outer right-hand position. The shaft transmits drive torque from the rear differenti...

Stub Axle Kit - Rear, replacement kit for the rear stub axle in the Salisbury rear axle assembly used on later Defender models. The rear stub axle...

Upper Swivel Pin forming the upper pivot of the front axle swivel housing. The pin bolts to the top of the swivel pin housing and runs in the uppe...

Swivel Pin Housing Shim - 0.010in is a 0.010 in (0.25 mm) shim used to set the bearing preload in the front axle swivel pin housing assembly. Fitt...

Soft Top Hood Retainer Spindle for the soft top retaining hardware. The spindle forms part of the hood retainer mechanism, providing the pivot or ...

Front Axle Assembly is the complete driven front beam axle, forming the front axle and final drive. It houses the front differential and mounts th...