Land Rover Defender Parts

4-Pin Relay is a multi-purpose electromechanical switching relay used throughout the vehicle's electrical system, where a low-current control signa...

See fitting instructions: https://www.scribd.com/doc/208898844/Fitting-Instructions-for-RTC3176-Adjuster-Shoes-Drum-brake-LAnd-Rover-Series

Brake Pipe Union - a male union fitting for 3/16" (4.75mm) hydraulic brake pipe, with a 7/16"-20 UNF thread. It clamps the flared pipe end against...

Hub mud shield

Timing Belt Tensioner for the 2.5L Td5 5-Cylinder Turbo Diesel engine timing system. The tensioner pulley bears directly against the timing belt a...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Rear Door Outer Waist Seal - Left-Hand fitted along the upper edge of the left-hand rear side door outer panel, sealing the interface between the o...

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Bonnet Buffer - rubber buffer at the bulkhead. This rubber buffer mounts at the bulkhead where the rear of the bonnet rests when closed, cushionin...

Axle Bump Stop - rubber bump stop for the front and rear suspension axle assemblies. Fitted to the chassis above each axle, the bump stop limits a...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Brake Pipe Clip - single-bore retaining clip for securing a rigid brake pipe to the chassis or body structure. This clip holds the brake pipe in i...

Enhance the ignition performance of your Land Rover Defender, Discovery 1, and Range Rover Classic (3.5 V8 carb & EFI models) with this high-qu...

Bulkhead Seal for the dash ventilation aperture on Defender models without air conditioning. This rubber seal fits between the dash ventilator ass...

Thermostat - 88°C for the cooling system of V8 petrol engines. The thermostat regulates coolant flow between the engine block and the radiator, al...

Door Lock Barrel Set for the body locking system, supplying replacement lock cylinders for the door and body locking points. The barrels integrate...

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Anti-Roll Bar Bush for the rear suspension. It locates and insulates the rear anti-roll bar (stabiliser bar) at its mounting to the chassis, allowi...

Door Hinge for the rear end (load/tail) door, lower position. One of the pair of side-hinged door hinges that mount the rear door to the body aper...

Rear Door Outer Waist Seal - Right-Hand fitted along the upper edge of the right-hand rear side door outer panel, sealing the interface between the...

Brake Pipe Clip - Double secures and routes rigid hydraulic brake pipes within the braking system. This double clip retains two brake pipes at a s...

Wheel Cylinder Overhaul Kit for front drum brake systems fitted with 11-inch brake drums. This kit provides the necessary parts to overhaul all fo...

Oil seal

Detent Spring for the manual gearbox gear selector mechanism. The spring loads the detent ball against the selector shaft, holding the selected ge...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Exhaust Rubber Mounting suspends the exhaust system from the chassis, supporting the silencer and pipework at its mounting points. The rubber elem...

Front Bumper for the front-end body structure, finished in black. The bumper mounts across the front of the chassis to form the front impact face ...

Heater Valve for the cabin heating circuit on Defender Puma diesel models from 2007 onwards. This valve regulates the flow of engine coolant to th...

Inside Door Handle Bezel The interior trim escutcheon that surrounds the door release handle on the inner door panel, finishing the opening around ...

Brake master cylinder

Oil Cooler O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel engine. This O-ring seals the oil cooler assembly and oil filter housing to the cylinde...

Timing Chain for the Rover V8 petrol engine, part of the camshaft drive assembly located in the front timing cover. This single-row roller chain t...

Headlamp Surround - Right-Hand - trim finisher that frames the headlamp on the front panel, surrounding the headlamp unit and locating against the ...

Reverse Light Switch for the R380 5-speed manual gearbox, completing the reverse lamp circuit when reverse gear is engaged. This switch threads in...

Exhaust Bush - Female is the female-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the...

Side Cover Gasket sealing the cylinder-block side cover (tappet inspection cover) to the block face, for petrol and diesel engines. The side cover...

Clutch Cylinder Adaptor - a pipe union that connects the hydraulic clutch supply pipe to the inlet port of the clutch master cylinder. Fitted at t...

Front direction indicator lamp for the vehicle lighting system. This unit provides the flashing directional signal function at the front of the v...

Clutch Release Plate for the LT77 5-speed manual gearbox clutch release assembly. This mounting plate fastens the external hydraulic clutch slave ...

Camshaft Oil Seal for the rear of the Td5 2.5L 5-Cylinder diesel engine. Fitted at the rear of the cylinder head camshaft bore, this seal prevents...

Wiper Drum Adaptor - splined adaptor used in the windscreen wiper system to connect the wiper arm to the splined wiper spindle. The adaptor seats ...

Lower Windscreen Hinge Gasket (large section), the seal fitted at the lower windscreen-to-bulkhead hinge bracket where the windscreen frame pivots ...

7" round LED headlamp 12/24V black 78W LHD (pair)

Thermostat Housing Gasket Seals the thermostat housing to the cylinder head within the cooling system of the 300 TDi 2.5L turbo diesel engine. It ...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Wiper Motor for the windscreen wiper assembly. It converts the electrical supply into rotary motion, driving the wiper transmission and linkage th...

Transfer Box Gear Change Bush for the LT230 transfer box gear change and differential lock linkage. This bush fits the gear change linkage connect...