Land Rover Defender Parts

Idler bracket and pulley TD5 non-ACE

Oil Filter Rotor is the rotating element of the centrifugal oil filter on the Td5 2.5L 5-cylinder turbo diesel engine. Mounted within the centrifu...

Coolant Bypass Hose for the thermostat assembly on the 3.5L V8 petrol engine. This hose connects the thermostat housing to the inlet manifold, pro...

Headlamp Surround Finisher - Left-Hand - black trim bezel that frames the headlamp on the front panel, surrounding the headlamp unit and locating a...

Bump Stop - Front for the front suspension travel limiting assembly. This rubber bump stop limits upward suspension travel at the front axle, prov...

Air Intake Hose for the 2.25 litre diesel engine, forming part of the air induction system between the air cleaner and the intake manifold. It car...

Axle Pinion Gasket for the Salisbury rear axle, sealing the pinion bearing retainer to the differential housing at the propshaft flange end of the ...

Accelerator Cable links the accelerator pedal to the injection pump throttle lever, forming part of the throttle linkage on the 2.25L diesel engine...

Exhaust Bush - Female is the female-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the...

O-Ring - an elastomer seal used at the oil cooler pipe connection within the engine oil cooler circuit. It seats in the union between the oil cool...

Rocker cover rubber washer petrol

Fuel Tank Mounting is the moulded rubber isolator in the fuel tank mounting assembly that sits between the tank body and its chassis support. It c...

Hinge Pin Kit containing the replacement hardware for door and rear tailgate hinges on Series and early Defender models. Fits the front and rear d...

Weatherstrip for the alpine light (side roof window) glass. This rubber sealing strip retains and seals the 5mm glass panels of the alpine lights ...

Fuel Pump Gasket for the 2.0L diesel engine (Series II) and 2.25L diesel engine (Series IIA). This gasket seals between the mechanical fuel pump b...

Shock Absorber for the front suspension on the short-wheelbase (SWB) chassis. Mounted between the front axle and the chassis, the hydraulic damper...

Track Rod End for the steering linkage, with a left-hand thread. The track rod end forms the ball-jointed connection between the steering link and...

Steering damper installed within the steering linkage assembly to control lateral movement of the track rod and reduce vibration transmitted throug...

Toggle Switch is a two-position on/off switch in the dashboard switchgear, controlling the instrument and panel lighting circuit. The sprung toggl...

Windscreen Wiper Motor for the front wiper system, supplied as a motor assembly with the integral reduction gear and park switch. Supplied without ...

7" round LED headlamp 12/24V black 78W LHD (pair)

Front Door Hinge - Upper, Left-Hand - upper hinge for the front door, mounted between the door and the body aperture. It forms the upper pivot of ...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Bulb Holder - double-filament bulb holder for an exterior lamp assembly, accepting a 5/21W (P21/5W) twin-filament bulb. The holder seats into the ...

Fuel Pump Seal, part of the fuel delivery system at the in-tank fuel pump and sender module. Seals the joint where the fuel pump and sender unit m...

Lock Washer for the gearbox mainshaft, securing the special retaining nut where the mainshaft meets the transfer box. A tab washer whose tang is b...

Rotor Arm for the Lucas distributor in the ignition system. Mounted on the distributor shaft beneath the cap, it routes the high-tension spark fro...

Rear Upper Shock Absorber Bracket, the upper mounting bracket for the rear damper within the rear suspension. It forms the fixed upper anchorage b...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Clutch Slave Cylinder Push Rod within the Clutch Actuation Assembly, transmitting hydraulic force from the external slave cylinder to the clutch re...

Gearbox Plug Sealing Washer for LT76 and LT77 manual gearbox drain, level, and inspection plugs. This sealing washer fits beneath the thread of ge...

Ancillary Drive Idler Pulley for the Td5 2.5L 5-Cylinder diesel engine. Located within the front-of-engine ancillary drive system, this pulley pro...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the Rover V8 petrol engine. It forms a coolant-tight joint bet...

Shim hinge

Track Rod Clamp is a split-tube collar that secures the threaded track rod end into the track rod tube on the front steering axle. Once the front ...

Carburettor Inlet Seal for the Zenith carburettor, in the engine air intake system. It seals the joint between the carburettor air intake and the ...

Brake shoe spring 109 rear lower

Bolt - 3/8" BSF x 1" hexagonal head bolt to British Standard Fine thread specification. 3/8" BSF (British Standard Fine) thread with a 1" shank le...

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Speedometer Cable connects the speedometer drive on the gearbox to the speedometer head in the instrument cluster. The rotating inner cable transm...

Fitment All TD5 diesel models up to (VIN) 6A999999 All TD5 diesel models All V8 EFi petrol models 2.5L 6 Cyl BMW Diesel /4.0L and 4.6L EFI V8 P...

Rear Drum Brake Shoe Set covering one full axle, sized for 11-inch rear drum brakes. The shoes carry the friction linings that press outward agains...

Rear Fog Lamp forming part of the rear lighting assembly, providing a high-intensity red rear light for use in poor visibility. It operates on its...

Nyloc Nut - 1/4" UNF - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under ...

Nut, 1/2" UNF. A threaded fastener used on the early 4-cylinder diesel engine assembly.

LT230 Drain Plug Joint Washer, used across the LT230 transfer box and a range of engine and drivetrain applications. This flat sealing washer seal...

Glow Plug for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It forms part of the cold-start pre-heating system. The glow ...

Vacuum Pump Gasket for the 2.5L 300TDi diesel engine, sealing the vacuum pump mounting face to the cylinder block. The vacuum pump is driven from ...