Land Rover Defender Parts

Steering Column Switch - Wash/Wipe - the column-mounted stalk switch that operates the windscreen wiper and washer functions. Mounted on the steer...

Speedo drive oil seal LT230

Gasket - LT76

Fan belt OEM DAYCO 10mm wide, 1235mm long

Water Pump Gasket seals the coolant pump to the engine front cover on the V8 petrol engine. It fits at the pump mounting face, sealing the coolant...

Side Panel Buffer, a rubber buffer fitted at the rear body side panels. Sits between the upper and lower rear quarter panels, cushioning the joint...

Drain Plug - a tapered threaded plug used to seal and drain fluid from engine and driveline housings. It serves as a coolant drain plug in the cyl...

Gerschikt voor 2.25 ltr benzine

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Manifold Stud - M8 x 36 mm - for the Td5 2.5L 5-cylinder turbo diesel engine. The stud threads into the cylinder head to locate the manifold flang...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Plain washer

Transmission Handbrake Shoe Set is the friction pair for the drum-type parking brake mounted on the rear output of the transfer box. When the hand...

Rotor Arm for the distributor ignition system. The rotor arm mounts on the top of the distributor shaft and turns with it. It picks up the high-te...

Condenser for the distributor ignition system. The condenser (capacitor) is wired across the contact breaker points inside the distributor. As the...

Wiper Arm - front windscreen wiper arm, right-hand. The 5mm is the narrow width of the arm, which sets the wiper-blade fitting - it is not a spind...

Shock Absorber Turret Bracket is the front suspension turret that caps the coil spring and carries the upper mounting of the front shock absorber. ...

P-shaped sill seal, 1983 - 1994

Oil Filter for the Td5 2.5L 5-cylinder turbo diesel engine, a cartridge element fitted in the engine oil filtration circuit. This is the short-len...

Gearbox rubber mounting LH

Swivel Pin Housing Joint Washer for the front axle swivel housing assembly. This joint washer seals the oil seal retaining plate to the face of th...

Swivel Shim is a 0.75 mm selective shim from the front axle swivel pin assembly. It is fitted beneath the upper swivel pin retaining plate, where s...

Swivel Pin Housing Shim - 0.13mm (0.005") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

Blind Spot Mirror is a wide-angle convex door mirror for the right-hand side, replacing the standard mirror to widen the rearward field of view and...

Clutch Pedal Assist Spring Kit - an over-centre helper spring for the clutch pedal that reduces the effort required to operate the clutch. Mounted...

Stainless Steel Bolt Kit for securing the front door hinges to the body on the 2-door Defender. The fasteners replace the original mild-steel fixin...

Rear Mudflap - exterior splash guard that mounts behind the rear wheel to deflect mud, water and road debris away from the underbody and following ...

Fitment: All models from (VIN) WA138480 on

Air Intake Blanking Plate closes off a wing-top air intake aperture in the induction system. This is the left-hand wing-top blank for left-hand-dr...

Radius Arm Bush - Front for the front suspension radius arm assembly. This rubber bush is pressed into the forward end of the front radius arm and...

Coolant Temperature Transmitter - Black mounted at the thermostat housing, supplying the coolant temperature signal to the instrument cluster tempe...

Brake Master Cylinder Repair Kit for the dual-line (split-circuit) braking system with direct-acting servo. This is a seal/overhaul kit that recon...

Reservoir kit

Brake Drum - 11 in - Large Wheel Studs is a cast iron drum for the drum brake assemblies of Series 3 and Defender models. The drum measures 11 inc...

Reflector SIII

Bolt securing the bulkhead to the chassis outrigger. A 1/2" UNF hex-head bolt used at the lower bulkhead mounting points, where the bulkhead fixes...

Joint Washer sealing the mounting joint between the cylinder block and the auxiliary unit driven off the engine: the vacuum pump on diesel engines,...

Exhaust Clamp for the exhaust-to-chassis mounting. Two-bolt upper clamp plate that forms the exhaust-to-chassis mounting assembly on Series and ea...

Spare Wheel Bonnet Strap, the retaining strap for a bonnet-mounted spare wheel. Secures the spare wheel in the bonnet-top carrying position, holdi...

Locking Fuel Filler Cap for the fuel tank filler neck. Two-lug bayonet fixing. The cap is vented, allowing the tank to equalise pressure as fuel i...

Wiper Blade, 315mm, for the windscreen and rear screen wash-wipe system. The blade carries the wiping element that sweeps across the glass to clea...

Shock Absorber - rear suspension damper for the short-wheelbase chassis. Mounted between the rear axle and the chassis bracket, it controls spring...

Distributor Cap for the Lucas distributor fitted to the four-cylinder petrol engine, part of the ignition system. The cap seats over the distribut...

Drag Link Ball Joint Kit for the steering box drop arm on power-assisted steering boxes. The ball joint forms the articulating connection between ...

Bodyside Seal for the lower edge of the rear upper body section, sealing the joint between the upper body structure and the lower body on the rear ...

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Air Intake Grille Panel - air intake grille installed within the air intake system housing, forming part of the intake ducting assembly upstream of...