Land Rover Defender Parts

Bearing used across several Land Rover drivetrain assemblies: the LT230 transfer box, where it supports the high and low range gear; the LT95 gearb...

Copper Washer is a soft sealing washer used to form a leak-tight metal seal at a threaded or banjo union. Positioned between a bolt or fitting and...

In/out member spring

Heater Duct, right-hand side, within the heater demister and air distribution system. Channels air from the heater assembly to the windscreen demi...

Cantrail Seal fits along the cantrail at the top of the rear cab, sealing the upper joint where the cab meets the roof. It runs the length of the ...

Glass seal EPDM

Barrel Lock and Key for the door lock, supplied as the keyed lock barrel together with a matching key. The barrel is the cylinder the key turns to...

Centre Squab Buffer - a rubber buffer that cushions the centre seat squab (backrest) against the surrounding bodywork. It prevents metal-to-metal ...

Past op  1958 - 61:   Sommige S 3 vanaf 1977 en 110 1983 - 84 All 3 Lug Internal Fixings

Pedal Pivot Bush is the bearing bush on which the clutch or brake pedal pivots within the pedal box assembly. Pressed into the pedal bore, it prov...

Bolt, 7/16" BSF x 1-3/8" secures the upper swivel pin to the swivel housing in the front axle assembly. The top swivel pin retains the swivel ball...

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

Dowel A locating dowel for the engine cylinder block and cylinder head assembly. It seats in machined bores to align the cylinder head to the bloc...

Air Suspension Connector joins the valve block to a high-pressure air line within the air suspension pneumatic circuit. The fitting forms a sealed...

Setscrew is a fully threaded hex-head fastener used as a general-purpose fixing across engine and cooling assemblies. Threaded 5/16" UNC with a 5/...

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

Cap - Pressure - Radiator

Head Gasket Set - V8

Contact Set - Lucas Distributor is the breaker-point set for the ignition distributor. Mounted on the distributor baseplate, the points are opened...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Rear Coil Spring Spacers, +2" - a pair of suspension spacers for the rear coil springs that raise ride height by approximately 2 inches (50 mm). E...

Oil Temperature Sensor is a transducer in the engine oil lubrication monitoring circuit, wired for 24V electrical systems. Threaded into the oil f...

Gearbox Heat Shield fitted to the transmission mounting assembly, protecting the surrounding components from exhaust and drivetrain heat. By reduc...

Radius Arm Bush - Front is the flexible mounting bush at the front radius arm-to-chassis location. The radius arm locates the front axle longitudi...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the replaceable big-end shell bearings that fit between the connecting rods an...

Clutch Master Cylinder Overhaul Kit for rebuilding a CV-type master cylinder, allowing the worn internal components to be renewed without replacing...

Silicone Intercooler & Turbo Hose Kit - a set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing the standard...

Ignition switch

Gear Lever Grommet for the LT85 manual gearbox gearchange assembly. Fitted around the base of the gear lever where it passes through the transmiss...

Shock Absorber for the rear suspension, within the Shock Absorbers & Springs assembly group. The damper mounts between the chassis and the rea...

Universal Joint for the propeller shaft assembly, transmitting rotational torque between adjoining shaft sections while permitting the angular move...

Conrod Bearing Set for the Td5 2.5L 5-cylinder turbo diesel engine, supplied at standard size. The connecting rod bearings (big-end bearings) sit ...

Main Bearing Set for the Td5 2.5L 5-cylinder turbo diesel engine. The main bearings are the crankshaft journal bearings seated in the cylinder blo...

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Bolt Secures the radius arm to the axle bracket within the radius arms & links assembly. Installed through the radius arm bush and axle mounti...

Connecting Rod Bearing Set for the 2.5-litre 4-cylinder engine, including the 200 TDi and 300 TDi diesels. These are the replaceable big-end shell ...

Spring Retaining Plate in the rear suspension, securing the upper end of the rear coil spring. It locates and clamps the top of the coil spring ag...

Cam Cover Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the camshaft cover to the cylinder head. This is the flanged-head bolt th...

Push Rod - a valvetrain component in the overhead-valve layout of the Rover V8 engine. It sits between the camshaft-driven tappet and the rocker a...

Steering Guard - 8mm Alloy - LHD - Black for underbody protection of the steering linkage assembly. Constructed from 8mm laser-cut alloy plate wit...

Gear Lever Housing for the 5-speed manual gearchange assembly. It mounts on top of the gearbox and locates the gear lever, carrying the pivot and ...

Brake caliper rear RH OEM

Modular Steel Wheel - Black - 7J x 16 A modular steel road wheel finished in black, sized 7J x 16 with an ET08 offset. The steel construction suit...

Heater Valve for the cabin heating circuit on Defender Puma diesel models from 2007 onwards. This valve regulates the flow of engine coolant to th...

Bulb Holder Assembly - Blue for the instrument panel illumination circuit. This holder and bulb assembly fits within the instrument cluster to pro...

Main Bearing Set - crankshaft main bearing shells for the 2.25L four-cylinder three-bearing engine. The main bearings support the crankshaft withi...

Wing Fixing Plate is a three-stud captive stud plate used in the front body mounting assembly, where it secures the front wing to the radiator (fro...

Upgrade your Land Rover Defender 90 & 110 (2002-2016) with this OEM-style Safari rear door, designed with pre-drilled spare wheel carrier holes...