Land Rover Defender Parts

Rear Fog Lamp - LED, 95mm round, clear lens, for North American Specification (NAS) Defenders. The lamp fits the standard 95mm round rear fog lamp...

Body blanking plug 12 X 18MM

M12 Nut used as a fastener at several chassis and running-gear locations, including the swivel pin housing, drive shaft fixings and front brake cal...

Fuel Connector Block for the Td5 2.5L 5-cylinder turbo diesel engine (Euro III, later specification). The block is the central junction of the fuel...

Bolt 5/16" UNC x 5" is a long mounting bolt for the coolant pump and power steering pump on the 3.5L V8 petrol engine. Its length carries the powe...

Brake Pad Set - Rear - a set of friction pads for the rear disc brakes, forming part of the rear braking assembly. The pads locate in the rear bra...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Spring Washer for use as a locking fastener component across Land Rover assemblies. A helical split spring washer providing resistance against fas...

Water-in-Fuel Sensor for the Td5 2.5L 5-cylinder turbo diesel fuel filter / sedimentor assembly. It threads into the base of the fuel filter housi...

Heater Blower Motor for the heater and ventilation assembly. Drives the blower fan that draws air across the heater matrix and distributes it throu...

Clutch Cover is the pressure plate assembly of the clutch, bolting to the engine flywheel within the clutch and gearbox coupling. Its diaphragm sp...

Gearbox Bearing for the R380 5-speed manual gearbox, measuring 35 × 72 mm. Fitted within the R380 transmission assembly, this rolling-element bear...

Intercooler Hose Kit - Silicone Black for the turbocharger and intercooler air circuit on the TD5 2.5L 5-cylinder turbo diesel engine in the Defend...

Shock Dropper - Rear - Pair: zinc-plated steel relocated rear shock absorber top mounts that lower the upper mounting point by 50mm. By relocating...

Rear Shock Absorber provides damping control within the rear axle spring and damper assembly for suspension set up with extended travel. Twin-tube...

Front suspension shock absorber designed to control spring oscillation and maintain tyre contact with the road surface. Twin-tube low-pressure ni...

Front Coil Spring - Heavy Load, Standard Height (Terrafirma). These front coil springs are rated for heavy load while retaining the standard ride ...

Bolt, M10 x 30: high-tensile metric setscrew with an M10 thread, 30 mm long.

Water Pump for the 3.5L Rover V8 petrol engine cooling circuit. Belt-driven from the front of the engine, the pump circulates coolant through the ...

Brake Pad Set - Front for the front hydraulic disc brake assembly. The pads are clamped by the caliper against the brake disc to generate friction...

Main Bearing Set for the Rover V8 engine, in the standard size. The main bearings are the crankshaft's principal support bearings, sitting between ...

Snatch Block - a winch recovery pulley used to redirect a winch line or to double its effective pulling capacity. Rated for a 10-tonne working load...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

Hex Head Bolt - 1/4" UNF thread, 5/8" long, with a hexagonal head. A general-purpose imperial fastener with a Unified Fine (UNF) thread form, driv...

Screw - No. 8 x 3/4" - a small imperial fixing used to secure the heater control panel to the dashboard. No. 8 gauge with a 3/4" length. Its short...

Windscreen Hinge Screw - the fixing that secures the windscreen frame hinge to the bulkhead, allowing the frame to be folded down on models fitted ...

Mirror Glass - the replacement reflective glass for the exterior door mirror. It seats into the mirror head on its backing plate, restoring a clear...

Gearbox Sump Gasket for the ZF 4-speed automatic transmission, sealing the joint between the transmission oil pan (sump) and the gearbox casing. T...

Heater Blower Motor Assembly for the heating and ventilation system, mounted in the heater box. The motor and fan draw air through the heater assem...

Clevis Pin for the handbrake (transmission parking brake) linkage. This 22mm clevis pin connects the handbrake operating rod to the relay lever, t...

Fuel Tank Bolt - a mounting bolt that secures the fuel tank to the chassis. It fixes the tank at its mounting point and is specified for the metal...

Exhaust Downpipe - LH - V8 is the left-hand front section of the exhaust system on V8 petrol applications. It connects the left-hand exhaust manif...

Side Window Seal is the rubber glazing seal that secures and weatherproofs the fixed side window glass within its body aperture. Part of the body ...

Heater Demister Hose - ducting hose within the heater demist circuit. Carries warm air from the heater box to the windscreen demister vents.

Bonnet Stay - Classic

Quarter Panel Valance - RH for the Defender 110 Station Wagon. This pressed steel valance panel forms the lower rear section of the right-hand rea...

Spill Rail for the 300 TDi fuel injection system. The spill rail links the leak-off unions at the top of the injectors and carries surplus fuel fro...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Rear Stop/Tail Lamp - LED, Smoked - LED combined stop and tail lamp with a smoked lens, supplied as a complete sealed unit to replace the standard ...

Stop/Tail Lamp - LED is a combined stop and tail light using LED illumination with a clear lens, mounted at the rear as part of the rear lighting. ...

Viscous Unit & Fan Assembly TD4 2.2 From (V)ca000001 Borg Warner

Trim Clip Interior trim retaining clip, grey. Secures interior trim panels to the body.

EGR Valve Gasket seals the exhaust gas recirculation (EGR) valve to its mounting flange within the exhaust gas recirculation circuit. It maintains...

Cylinder Head for the Td5 2.5L 5-cylinder turbo diesel engine, later type. The cylinder head seals the top of the engine block, forming the combust...

Nut - 10/32" UNF A nut with a #10-32 UNF (Unified National Fine) internal thread, run onto a matching UNF bolt or stud to clamp the joint.

Differential Flange Mud Shield - a protective shield fitted at the differential pinion drive flange. It sits behind the drive flange, where the pr...

Fitment: All models (VIN) LA930456 on

Brake Disc - Solid - Front is the front brake disc, mounting to the wheel hub and providing the friction surface the brake pads clamp against durin...