Land Rover Defender Parts

Self-Tapping Screw - Black is an M8 x 25mm self-tapping screw with a black finish. The self-tapping thread cuts its own mating thread as it is dri...

Differential Bearing for the Salisbury axle. It is one of the pair of taper roller bearings that carry the differential carrier - the housing holdi...

Coil Spring - Front - +2" Light Duty is a front suspension coil spring providing approximately 50mm (2 inches) of lift above the standard ride heig...

Tow Electrics Wiring Harness - N Type Socket - plug-in wiring harness providing an N-type 7-pin socket at the towbar, enabling connection of traile...

Spring Washer for use across a wide range of fixings and assembly applications on Land Rover vehicles. This split-ring spring washer is placed ben...

Fuel Pipe - Filter to Injection Pump for the Defender 300TDi 2.5L diesel (non-EGR). This pipe carries filtered diesel from the fuel filter housing...

Fuel Filter Holder - With Filter for the Defender Puma diesel fuel system. This complete filter assembly mounts in the engine bay fuel circuit and...

Past op 90 2.5L TD5 diesel modellen vanaf (VIN) WA159807 on

Plain Washer in M6 oversize form, with a larger outer diameter than a standard M6 washer. It spreads the clamping load of a bolt head or nut over ...

Taper Roller Bearing - the mainshaft bearing used in the LT77 and R380 five-speed manual gearboxes, located at the rear of the primary pinion where...

Shock Absorber Bush Kit for the mounting points of Terrafirma TS-series shock absorbers. The kit provides the hardware required to replace worn bu...

Return to Centre Steering Damper for installation within the steering linkage assembly. This unit mounts between the axle steering arms and the st...

Spring Retaining Plate - Rear for the rear coil spring seating assembly on Defender 110 and 130. Coil springs can become dislodged from their axle...

Turret Securing Rings - Front are reinforcement rings that fit around the front shock absorber top mount aperture in the inner wing. They distribut...

Sport Front Grille & Headlamp Surround Kit - a front-end exterior styling set that replaces the factory front grille and headlamp surrounds. I...

Rear Coil Spring for the rear suspension, fitting between the axle and the chassis spring seat to support the vehicle and absorb road inputs. This...

Piston Ring Set - a ring set for one piston of the Rover V8 petrol engine. The set comprises the compression rings and the oil control ring that s...

Brake caliper repair kit front

Taper Roller Bearing - outer pinion bearing in the differential final drive assembly. The drive pinion is carried on a pair of opposed taper rolle...

Hex Bolt - a hexagonal-head bolt with an M6 metric thread and a 12 mm length, manufactured to property class 8.8. Class 8.8 is a medium-carbon ste...

Heater Knob Screw for the heater control assembly. This screw secures a control knob to its spindle on the heater control panel.

Brake Pad Set for the front axle disc brake assembly, for use with solid (non-vented) front discs. The pads locate within the front calipers and cl...

Shroud Screw - a fixing screw used to secure the steering column shroud and other trim and bracket assemblies. Metric M5 thread with a 40 mm shank...

Rear suspension panhard rod retaining bolt used in the Radius Arms & Links assembly. This bolt secures the panhard rod to its mounting bracke...

Nut - 2BA, a small-diameter fastener in the British Association (BA) thread standard. 2BA refers to the No.2 size within the British Association t...

Diesel startermotor military reconditioned EXCHANGE!!

Piston for the 2.5L four-cylinder petrol engine, running in the cylinder bore within the piston, connecting-rod and bearing assembly. Supplied at ...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Temperature Transmitter is the coolant temperature sender within the engine cooling and instrument gauge circuit, for V8 petrol applications and ca...

Windscreen Washer Reservoir is the fluid storage tank for the screen wash system, holding the washer fluid that is delivered to the wash jets. The...

Belt Drive 2.4tdci Non-a/C 2621mm

Turbocharger for the Td5 2.5L 5-cylinder turbo diesel engine. The turbocharger draws energy from the exhaust gas stream to drive a compressor whee...

Radiator Assembly for the engine cooling system on TD5 and TD4 (Puma) diesel applications. The radiator sits at the front of the cooling circuit, c...

Front Radius Arm Nut - an M16 self-locking Nyloc nut used at the front radius arm mounting, part of the front suspension linkage. The radius arm l...

Rear Silencer Pipe forms the rearmost section of the exhaust system, combining the rear silencer (muffler) with an integral tailpipe. It installs ...

Clamp bracket lower for steering column shroud

Fuel Tank Bolt - shouldered mounting bolt in the fuel tank support assembly, securing the tank mounting to the chassis outrigger. The plain should...

Blind Nutsert (M6) is a threaded insert that provides an M6 female thread in thin sheet metal or panels where the rear face is not accessible. It ...

Starter Motor - Defender TD4

Window Channel for the rear quarter window, part of the rear quarter glazing. Forms the run channel that guides and seats the sliding glass. The c...

Glazing felt strip for the door top sliding glass channel. The felt lines the channel the sliding glass runs in. It cushions the pane, takes up th...

Alpine Light Glass is a fixed side window for the raised roof section of the body. It glazes the Alpine light aperture in the upper body side, abov...

Pull Ring for the rear seat lock release. It operates the split rear seat lock mechanism, releasing the seat squab so the backrest can be folded d...

Tailgate Hinge for the left-hand side, the lower hinge on which the drop-down tailboard pivots. It carries one side of the tailboard along its low...

Tailgate Hinge for the right-hand side, the lower hinge on which the drop-down tailboard pivots. It carries one side of the tailboard along its lo...

Heater Blend Knob Screw - retaining screw securing the heater blend control knob to its spindle. Part of the heater control assembly.

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Front Indicator Lamp - LED is an LED front direction-indicator with a smoked lens, replacing the conventional filament indicator on the front of th...