Land Rover Defender Parts

Roof Centre Console for the Defender Hard Top and Station Wagon interior headlining. The console features a single DIN radio aperture with removab...

Anti-Roll Bar Spacer Kit - 2-Hole for Land Rover Defender. These spacers are used to correct the anti-roll bar drop link geometry on lifted Defend...

Side Locker - a stainless steel storage box that mounts in the rear side quarter, set behind the inner rear wheel arch on the left-hand side. The ...

Silicone Hose Kit Puma 2.4 - Defender - Blue

Rear Bumper Corners are a pair of heavy-duty wraparound bumperettes that protect the vulnerable rear corners and sill ends of the bodywork. The po...

Front Spring Spacers fit between the front axle and the base of the front coil spring to raise the spring mounting point. The spacers are 50mm (2 ...

Twin Shock Mount Kit - Rear provides the additional mounting points required to run twin rear shock absorbers on each side of the rear axle. The ad...

Adjustable Panhard Rod - Long - lateral axle locating link within the suspension assembly, supplied in the longer length variant. The Panhard rod ...

Terrafirma Pro Sport Suspension Kit - Medium Load, +2" (50mm) Lift for Defender 110 and 130. This is a RAISED suspension kit: it lifts the vehicle...

Suspension Kit providing 2 inches of lift in a heavy load configuration, combining rated coil springs with All Terrain shock absorbers. The heavy ...

Terrafirma All Terrain Suspension Kit - Light Load, +2" (50mm) Lift for Defender 90, Discovery 1 and Range Rover Classic. This is a RAISED suspens...

Shock Absorber - rear suspension damper with four-stage adjustable damping, for standard ride-height travel. Fitted between the chassis and rear a...

Shock Absorber - front suspension damper with four-stage adjustable damping, for standard ride-height travel. Fitted between the chassis and front...

Big Bore Expedition Shock Absorber - front position, standard ride height. The damper installs between the front axle mounting and the chassis bra...

Wide Wheel Arch Extension Kit replaces the standard wheel arches with extensions that sit 50 mm (2 in) wider, giving additional coverage over wider...

Rear Coil Springs - Medium Load, +2" Lift (Terrafirma), supplied as a pair. This is a LIFT spring: it raises the rear by approximately 2" (50mm) o...

Coil Springs are a matched front pair that raise ride height by 2 inches (50 mm) above standard, forming part of the coil-sprung front suspension. ...

Power Steering Box of the Adwest lightweight type, right-hand drive, supplied complete with the drop arm. The steering box is the mechanical heart...

Fuel Injector Pipe - Cylinder 1 forms part of the high-pressure fuel injection circuit on the 2.5L 200TDi turbo diesel engine. This rigid steel li...

Wheel Cylinder Brake - RH

Windscreen Wiper Ferrule for the windscreen wiper mechanism — the splined bush that couples the wiper arm to the drive spindle. The ferrule fits o...

Fusible Link - 30A Pink for the electrical protection circuit. A fusible link that installs inline within the wiring harness at a current-protecte...

Fusible Link is a sacrificial circuit-protection device used in the vehicle electrical system. Rated at 60A and identified by its yellow body, it ...

Fusible Link - 100A Blue for the primary electrical protection circuit. A high-current fusible link that installs inline within the wiring harness...

Sidelamp Lens - White is the white/clear lens unit for the front sidelamp, part of the front exterior lighting cluster. The lens seats into the si...

Taper Roller Bearing - Differential Pinion - Inner supports the drive pinion shaft within the differential crownwheel and pinion assembly. The inn...

Sealing Washer - sump plug sealing washer for the ZF four-speed automatic gearbox. Fitted under the head of the transmission sump drain plug, the ...

Allen Head Screw is a body fixing used on the hinged windscreen frame of classic Defender models. The socket (Allen) head allows the screw to be d...

Brake Pipe Rear - Defender 90 1987-2006 - LH

Countersunk Screw - a machine screw with a flat, cone-shaped head that seats flush with the surface it fixes, leaving no proud edge. Metric M6 thr...

Rear Brake Caliper Pistons for the rear disc brake caliper. Each piston runs in a caliper bore behind the square-section piston seal and dust boot,...

Pan Head Screw, M6 x 12mm. Metric pan head screw for use across a range of Land Rover body, chassis, and electrical assemblies.

Tow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...

Front Outer Wing - Aluminium - LH for the Defender 90 and 110, supplying the left-hand front wing panel in the original aluminium construction. Th...

Front Brake Caliper, left-hand, for the non-vented (solid disc) front braking circuit. The caliper mounts to the front axle and houses the hydraul...

Front Brake Caliper - right-hand side, for the non-vented (solid) front disc installation. The caliper straddles the brake disc and carries the hy...

Alternator - belt-driven charging unit of the A133 type, rated at 65 amps. Driven from the crankshaft pulley, the alternator carries the vehicle's...

Alternator rated at 45A for the 3.5 litre V8 twin-carburettor petrol engine. Driven by the auxiliary belt as part of the engine charging system, i...

Main Bearing Kit 010 King

Size/Diameter: 1 inch

Piston Ring Set for one piston in the engine's piston and cylinder assembly. The rings seat in the piston ring grooves, sealing combustion pressure...

Piston Ring Set for one piston in the engine's piston and cylinder assembly. The rings seat in the piston ring grooves, sealing combustion pressure...

Piston Ring Set for the 2.25L 4-cylinder petrol engine, ground to +0.010" (0.25mm) oversize for use with rebored cylinder bores. The rings seal th...

Piston for the 2.25L 4-cylinder petrol engine, forming the reciprocating member within the cylinder bore that transmits combustion pressure through...

Jubilee Hose Clip for securing rubber hoses at coolant pipe, heater hose, and similar fluid circuit connections. The worm-drive band tightens evenl...

Connecting Rod Bearing Set for the 2.5L 4-cylinder engine, supplied in standard size. These are the big-end shell bearings that fit between the cr...

Main Bearing Set for the crankshaft of the 2.5-litre four-cylinder petrol and naturally aspirated diesel engines. Supplies the complete set of mai...