Land Rover Defender Parts

Exhaust Mounting Rubber - flexible support that suspends the silencer section of the exhaust system from the vehicle underbody. The moulded rubber...

Brake Union for the hydraulic braking circuit, with male 7/16"-20 UNF thread for 1/4" diameter brake pipe. This male-threaded end fitting connects...

LT230 Intermediate Shaft O-Ring, sealing the intermediate shaft within the LT230 two-speed transfer box main casing. The intermediate shaft transm...

Rear Stop/Tail Lamp - combined rear stop and tail lamp, supplied as a complete lens and body assembly. It mounts in the rear lamp position and pro...

Wiper Spindle Kit: the front wiper wheel box assembly that houses and supports the wiper arm spindle. Fitted in the scuttle, the wheel box guides ...

Needle Roller Bearing for the front axle swivel pin housing. The bearing seats in the swivel housing bore and carries the stub axle, providing rad...

Steering Box Seal Kit - Sector Shaft

oil filter OEM Hengst Fits: - Defender Puma 2.2L - Defender Puma 2.4L - Discovery Sport 2.2L D 16V - Freelander2 2.2L D 16V - Range Rover Evoque 2...

Split Pin

Front Propshaft for the 4-cylinder 2.25L petrol driveline. It transmits drive from the transfer box front output to the front axle differential, de...

Fuel Pump - Petrol 4-Cyl for the mechanical fuel delivery system on Land Rover 2.25L 4-cylinder petrol engines. This mechanical lift pump is drive...

Brake Light Switch

Courtesy Lamp Switch is the door-pillar plunger switch in the interior lighting circuit. Mounted in the door aperture, it is released when a door ...

Nyloc Nut with a 3/4" UNF thread, used as a locknut on heavy suspension joints. A nylon insert set into the crown of the nut deforms over the bolt...

Flange Bolt securing the rear output (propshaft) drive flange to the output shaft of the LT230 transfer box. Manufactured to a high-tensile specif...

Centre Cubby Box finished in black vinyl, fitting the centre position between the front seats to provide an enclosed storage compartment with a mou...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Fir Tree Fastener secures interior body and roof trim panels to the vehicle structure. The ribbed, tapered fir-tree shank pushes into a panel hole...

Speedometer Cable Plate Screw secures the speedometer cable retaining plate to the gearbox. It clamps the plate that holds the speedometer drive c...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Reverse Gear Selector Detent Spring for the manual gearbox selector mechanism. The spring loads the detent ball against the reverse selector shaft...

Shock Absorber Washer for the rear suspension, outer position. This washer fits over the rear shock absorber mounting, seating against the rubber ...

Oil Pressure Switch for the V8 petrol engine, forming part of the engine oil pressure warning circuit within the lubrication system. The switch th...

Drop Arm Ball Joint Kit for renewing the ball joint that connects the steering box drop arm to the drag link. The joint transmits steering input f...

Fuel Filter Element for the carburettor fuel supply circuit on Land Rover V8 petrol engines. Fitted in-line on the fuel feed pipe between the fuel...

Sliding Window Glass Felt - Rear Guide is the felt guide strip for the rear sliding side window. It installs within the sliding glass channel of t...

Diesel Fuel Decal is the self-adhesive caution label applied at the fuel filler to identify the tank as diesel. It marks the filler point so the v...

Serrated Washer with a 3/8" bore, a serrated locking (shakeproof) washer. Fitted beneath a bolt head or nut, the serrated teeth bite into both the...

Split Pin used throughout the chassis, steering and driveline assemblies as a positive locking fastener. The pin is passed through a cross-drilled...

Water Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...

Slipper pad

Front Cover Gasket seals the timing cover to the front face of the cylinder block on the V8 petrol engine. It fits between the front cover and the...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Front Propshaft Flange Bolt Kit - the high-tensile fasteners that secure the front propshaft to its mating flanges at the transfer box and axle end...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Bolt, 1/4" BSF x 1", serving as the steering lockstop in the front axle steering assembly. The bolt threads into the swivel housing and is set to l...

Drive Shaft Housing Bolt securing the drive shaft (swivel/stub axle) housing to the axle case. An M10 double-hex (twelve-point) headed bolt used a...

Toggle Switch is a two-position on/off switch in the dashboard switchgear, controlling the instrument and panel lighting circuit. The sprung toggl...

Drive Pin Fastener is a two-piece push-in fixing used to retain interior trim and ducting panels. The fastener body is pushed through aligned hole...

Fuel Connector Assembly - Pressure Regulator forms part of the fuel pressure-regulation circuit, providing the mounting and connection interface fo...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Weber Carburettor for the 2.25L petrol engine, part of the fuel and induction system. It meters fuel into the incoming air stream to form the air/f...

Heater Blower Duct Seal for diesel applications, fitted in the heater air intake. This foam seal sits between the air inlet duct and the heater blo...

Glass Fuse rated at 10A, a cartridge-type fuse used in the vehicle electrical system. The fuse seats in the fuse box or an inline fuse holder and ...

Bolt for the suspension mounting. A 7/16" UNF thread bolt of 6.5" length, used at the upper suspension mounting to secure the shock absorber and sp...