for Discounts / VAT
for Discounts & Correct VAT
Genuine, OEM, and quality aftermarket Land Rover Defender parts for the classic 90, 110, and 130 (1983-2016) and the new Defender L663 (2020-present). Every component is sourced for verified fitment by VIN and shipped from our Netherlands warehouse as part of our wider Land Rover parts catalogue.
Front Mudflap Brackets - a pair of stainless steel brackets that carry the front mud flaps at the rear of the front wheel arches, forming part of t...
View full detailsManifold Absolute Pressure (MAP) Sensor for the air intake and emission control system. The sensor mounts in the intake manifold and measures the ...
View full detailsRear Corner Kit - Black - 110 - Pre-07
Wiring Harness - Front Wing is a body wiring harness that runs along the inner face of the right-hand front wing, forming part of the front-end bod...
View full detailsRear Mudflap Brackets - Pair - 90
Exhaust Gas Temperature Sensor for the diesel particulate filter position in the exhaust after-treatment system of the 2.2L Puma TDCi diesel engine...
View full detailsOil Seal for the oil level sensor where it passes through the wall of the oil pan (sump). The sensor is retained in the sump and this ring forms t...
View full detailsOxygen (Lambda) Sensor - centre position sensor in the exhaust front pipe and catalyst assembly. Measures the residual oxygen content of the exhau...
View full detailsFuel Filter Relocation Kit - bracket kit that repositions the diesel fuel filter and eases the fuel pipe routing where the standard filter location...
View full detailsPlastic Rivet is a push-fit fastener that secures front engine-compartment insulation panels to the body. It locates into a pre-formed panel hole t...
View full detailsCylinder Head Bolt secures the cylinder head to the engine block on V6 and V8 petrol engines. Threaded M11 x 178 mm. Twenty bolts are required per...
View full detailsNumber Plate Lamp - LED is the rear licence plate illumination unit within the rear lighting circuit. It mounts above the licence plate at the rea...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsTyre Pressure Sensor (TPMS) for the direct tyre pressure monitoring system. Fitted at the wheel valve inside the tyre, it measures tyre pressure an...
View full detailsBump stop spacers, supplied as a pair, fitted between the chassis bump stop mounting and the bump stop itself. Each spacer packs the bump stop dow...
View full detailsBonding Lead - earth strap within the chassis wiring harness. Provides a low-resistance earth path between the body and the chassis, maintaining e...
View full detailsCylinder Head Gasket seals the cylinder head to the engine block on the 2.0L Ingenium four-cylinder diesel engine (AJ200 series). It seals the com...
View full detailsCylinder Head Gasket seals the cylinder head to the engine block on the 2.0L Ingenium four-cylinder diesel engine (AJ200 series). It seals the com...
View full detailsFuel Rail Pressure Sensor for the 2.2L turbo diesel common-rail fuel system. Mounted on the fuel supply manifold (fuel rail), it measures the pres...
View full detailsHandbrake Disc - transmission-mounted brake disc, the rotating element of the disc-type transmission handbrake conversion. Mounts on the transfer ...
View full detailsWading Kit - 2.4 Puma
Storage Box Mounting Brackets - bracket set that secures expedition storage boxes to a T-slot roof rack. The brackets clamp into the rack's T-slot...
View full detailsRear Shock Absorber - Heavy Duty - hydraulic telescopic damper for the rear coil-sprung suspension, mounted between the axle bracket and the chassi...
View full detailsChequer Plate - Rear Quadrant - Pair protects the rear quadrant panels - the body sections behind the rear wheel arches - from stone chipping, scuf...
View full detailsRear Shock Absorber - Heavy Duty - hydraulic telescopic damper for the rear coil-sprung suspension, mounted between the axle bracket and the chassi...
View full detailsRear Quadrant Chequer Plate, Pair - protective body panelling for the rear quadrant panels, supplied as a matched left and right pair. Manufacture...
View full detailsSensor - Wheel Speed
Sensor Assembly
Brake Pad Set for the rear foundation brake assembly, supplied as a complete axle set covering both rear wheels. The pads sit in the rear caliper ...
View full detailsPower Steering Hose in the hydraulic power steering circuit, connecting the fluid reservoir to the power steering pump. It carries fluid from the ...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsAutomatic Transmission Fluid (ATF), supplied in a 1 litre container. Specified for the automatic transmission and, where applicable, the power ste...
View full detailsExtreme Rear Body Corners - Pair - 110
Cylinder Head Bolt Kit for the 2.0L Ingenium diesel engine (AJ200 / AJ20D4). Supplied as a set for renewing the cylinder head bolts when the cylin...
View full detailsCylinder Head Bolt for the 2.0L Ingenium diesel engine (AJ200 / AJ20D4), securing the cylinder head to the engine block. Supplied as a single bolt...
View full detailsHex-Head Bolt, M12 x 80 mm for the accessory drive of the 2.2L Puma turbo-diesel engine. The bolt secures components in the pulley and drive-belt ...
View full detailsStainless steel braided brake hose kit, four-line, +2" extended length. The flexible hoses carry hydraulic pressure across the moving joint between...
View full detailsTread Plates - Front Bumper - punched and serrated alloy plates for the top faces of a Terrafirma front bumper. Supplied as a pair. Part of the fr...
View full detailsFully synthetic engine oil, SAE 5W-40 - 5 litre container. Engine lubrication system. A 5W-40 multigrade: the 5W winter rating gives cold-start fl...
View full detailsFully synthetic engine oil, SAE 5W-30 - 1 litre container. Engine lubrication system. Formulated for applications specifying Ford WSS-M2C913-D, an...
View full detailsFully synthetic engine oil, SAE 5W-30 - 5 litre container. Engine lubrication system. Formulated for applications specifying Ford WSS-M2C913-D, an...
View full detailsFully synthetic engine oil, SAE 5W-30, ACEA C1 - 5 litre container. Engine lubrication system. ACEA C1 is a low-SAPS classification - reduced sulp...
View full detailsFully synthetic engine oil, SAE 5W-40 - 1 litre container. Engine lubrication system. A 5W-40 multigrade: the 5W winter rating gives cold-start fl...
View full detailsFully synthetic engine oil, SAE 5W-30, ACEA C1 - 1 litre container. Engine lubrication system. ACEA C1 is a low-SAPS classification - reduced sulp...
View full detailsWing Top Protector Kit - chamfered protector panels for the front wing tops. The panels cover the wing top, the area most exposed to scuffing from...
View full detailsTiming Chain Tensioner, part of the timing chain drive within the timing cover. It applies controlled load to the timing chain guide to keep the ch...
View full detailsManifold - Heater
Parts for the full Land Rover Defender range, from classic Defender 90, 110 and 130 models built between 1983 and 2016 to the new Defender L663 introduced in 2020. Genuine, OEM and aftermarket parts in EU stock. Use the collections below to shop by generation.
The Land Rover Defender name covers two distinct vehicle platforms that share a name but little else in terms of engineering, parts compatibility, or servicing requirements.
The classic Defender (1983 to 2016) was a body-on-frame utility vehicle produced in 90, 110, and 130 wheelbase variants. It ran a series of diesel and petrol engine options across its production life, from early 2.25 petrol and diesel units through the 200Tdi, 300Tdi, Td5, and the later 2.4 and 2.2 Puma TDCi engines. Parts for these models are covered in the Defender 90, 110 and 130 parts collection.
The new Defender (2020 onwards) uses a monocoque architecture on Land Rover's D7x platform, which is also used by the Range Rover L460 and Range Rover Sport L461. It is produced in 90, 110, and 130 body configurations and is offered with a range of petrol and diesel engines including the P300, P400, D200, D240, and D300 units. Parts for these models are covered in the new Defender parts collection.
Parts are not interchangeable between the two platforms. If you are unsure which generation you have, use the guidance below before adding to your basket.
Fitment NotesConfirming your generation before ordering is the most reliable way to avoid returns and delays.
The simplest check is the model year. Classic Defenders were produced from 1983 to January 2016. New Defenders entered production from September 2020. There is no Defender model year between 2016 and 2020.
For the classic Defender, the chassis number (VIN) is stamped on the chassis rail on the right-hand side of the engine bay and also appears on a plate fixed to the bulkhead. The VIN encodes body style, engine type, and build year. For the new Defender, the VIN is found on a plate in the engine bay and is also visible through the windscreen on the lower driver-side corner.
If you have your VIN, use the parts search on roverparts.eu or contact Budget Parts directly. Providing your VIN removes ambiguity from fitment, particularly for engine-dependent parts such as gaskets, filters, sensors, and drivetrain components.
Quality TiersBudget Parts stocks three quality tiers across the Defender range. Understanding the difference helps you choose the right part for your build stage, budget, and use case.
Genuine parts are manufactured by Land Rover's approved supply chain and carry Land Rover branding. They are the exact specification used in original assembly. Genuine parts are typically the highest-cost option and are best suited to vehicles being maintained to manufacturer specification, vehicles under warranty, or restorations where originality matters.
OEM parts are manufactured by the same component suppliers that produce parts for the Land Rover production line, but are sold without Land Rover branding. The component itself is often identical to the genuine part. OEM is a strong choice for mechanical replacements where factory specification is required but original branding is not.
Aftermarket parts are produced by third-party manufacturers to a compatible specification. Quality varies by manufacturer and by part type. Budget Parts selects aftermarket lines that meet the fitment and durability requirements of the application. Aftermarket is well suited to high-wear items, body components, and non-safety-critical parts where cost efficiency matters.
All three tiers are clearly labelled on every product listing.
Parts CategoriesThe Defender range is supported across all major parts categories. Both the classic and new platforms are represented, though stock depth varies by generation and component type.
Categories stocked for the Defender range include body and chassis parts, brake parts, clutch system and kits, cooling parts, driveshaft and propshaft parts, electrical parts, engine parts, exhaust parts, fuel system parts, interior parts, lighting parts, service and maintenance parts, suspension parts, and wheels and wheel parts.
For model-specific category depth, navigate into the relevant child collection first and then apply a category filter, or use the category filter on this page alongside the Defender Classic or Defender New model filter.
EU Stock and DispatchBudget Parts operates from The Hague, Netherlands, with warehouse stock available for EU-wide dispatch. Parts marked in stock are held at the warehouse and are available for same-day dispatch on orders placed before the daily cut-off. Backorder is available on parts not currently in stock, with lead times confirmed at the time of order.
Trade and workshop buyers can apply for a wholesale account through the portal linked in the site header. Volume pricing is available on high-turnover lines including filters, brake components, fasteners, and service items.
Platform designation data for the D7x architecture is consistent with Land Rover's published product and technical documentation. The Discovery 5 (L462) uses the related but distinct D7a platform and is not covered by this collection. For VIN decoding and chassis-specific parts identification, the Land Rover JTIS (Jaguar Land Rover Technical Information System) and the relevant Land Rover parts catalogue are the authoritative references.
The articles below cover Defender-specific identification, platform differences, and parts selection in more depth. Each links back to this collection for parts.
A practical Defender buying and parts guide covering TD5 injector faults, 2.4 TDCi DPF issues, brake corrosion, and L663 fitment notes. Useful for both classic and new Defender owners researching parts before purchase.
Defender parts Europe 2025 →A guide to common faults on the 300Tdi classic Defender, with diagnostic notes, the fixes that actually hold, and the proven upgrades worth doing. Useful before ordering 300Tdi engine, cooling, or service parts.
Defender 300Tdi faults →Common 2.4 TDCi Puma faults explained, including DPF blockage, EGR issues, turbo underboost, clutch failure, and MT82 gearbox problems. Covers what to check and the parts most often involved.
Defender 2.4 TDCi problems →The classic Defender (1983 to 2016) is a body-on-frame vehicle. The new Defender (2020 onwards, internal designation L663) uses a monocoque architecture on the D7x platform. The two platforms are entirely different in construction, engine family, and parts fitment. No mechanical parts are interchangeable between them. Always confirm your model year before ordering, and use your VIN to resolve any fitment uncertainty.
The easiest check is the model year. Classic Defenders were produced from 1983 to January 2016. There are no Defender models from 2017 to 2019. New Defenders entered production in 2020. If you are unsure of the year, the VIN plate on a classic Defender is located on the chassis rail in the engine bay and on the bulkhead. On the new Defender, the VIN plate is in the engine bay and is also visible through the lower driver-side corner of the windscreen.
Yes. Budget Parts stocks all three quality tiers for both the classic and new Defender where available. Genuine parts carry Land Rover branding and are built to original assembly specification. OEM parts are manufactured by the same suppliers that supply the Land Rover production line, without brand labelling. Aftermarket parts are third-party components selected for fitment compatibility. Each listing on roverparts.eu clearly identifies which tier the part belongs to.
Yes. Budget Parts dispatches EU-wide from its warehouse in The Hague. Delivery is available across all EU member states. Shipping costs and estimated delivery times are shown at checkout based on your delivery address. Parts marked in stock are available for same-day dispatch on orders placed before the daily cut-off.
Yes. Budget Parts operates a wholesale portal for trade buyers, workshops, and resellers. You can register through the wholesale portal linked at the top of the site. Trade accounts provide access to volume pricing on high-turnover lines including service items, brake components, filters, fasteners, and drivetrain parts. There are no minimum order requirements to open an account.