Land Rover Defender Parts

Brake Pad Kit - Caliper

Brake Pad Set - Rear - friction pad axle set for the rear disc brake assembly. The pads locate in the rear caliper carriers and clamp against the ...

Rear Door Wiring Harness - the door-side section of the body electrical system, passing through the door pillar grommet into the rear side door. T...

Monotube Shock Absorber for either the front or the rear damper position of the coil sprung suspension, working alongside the coil spring to contro...

Front Brake Disc, 363 mm diameter - front foundation brake assembly. The disc locates on the front hub and provides the friction surface for the f...

Front Door Wiring Harness - driver's side front door harness in the body electrical system. It crosses from the A-post into the door through the h...

Front Brake Disc - Ventilated, Wavy, Cross-Drilled and Grooved. Ventilated front brake disc with a wavy outer profile and a cross-drilled and groo...

Rear Door Organiser - MOLLE-pattern storage panel mounted to the inside face of the rear door. The webbing grid accepts MOLLE-compatible pouches a...

Rear Corner Kit - Black - 110 Defender 07 On

Exterior mirror motor - left-hand side glass adjustment motor within the door mirror head. The motor sits behind the mirror glass and drives the g...

Camshaft Position Sensor mounted in the timing gear cover, reading the toothed target on the camshaft drive to give the engine control module a dir...

Thermostat Housing for the 5.0-litre AJ133 V8 petrol engine, part of the engine cooling circuit. The housing seats the coolant thermostat and form...

Remote Control Receiver is part of the vehicle anti-theft alarm system, operating on the 433MHz radio frequency band. It receives the coded radio ...

Monotube Shock Absorber for the front damper position of the coil sprung suspension, working alongside the coil spring to control body movement and...

Monotube Shock Absorber - Rear - Standard Travel is a high-pressure gas damper for the rear axle damping assembly, built to standard closed and ext...

Monotube Shock - Fr & RR +5"

Monotube Shock Absorber for the front damper position of the coil sprung suspension, working alongside the coil spring to control body movement and...

Turbocharger Circlip - retaining clip for the turbocharger actuator on diesel turbocharger installations. It secures the actuator rod to the contr...

Flanged Nut - M6 captive nut, also described as a U-nut or speed clip, used to provide a threaded fixing point in sheet metal and moulded panels. ...

Sound Deadening Panel reduces road, transmission and drivetrain noise transmitted through the floor into the cabin. The self-adhesive damping pane...

Stud used in the rear body upper fixings. The stud provides the threaded shank at the upper mounting points where the rear body ties into the vehi...

Lower Door Panel Assembly

Exhaust Gas Temperature Sensor for the lower sensing position at the diesel particulate filter, within the exhaust aftertreatment system. The sens...

Transmission Brake Backplate - the mounting plate for the drum-type transmission parking brake on the rear output of the LT230 transfer box. The b...

Brake Disc & Caliper Bolt - a fixing bolt for the brake disc and caliper assembly. It is used at both the front and rear brake disc and calipe...

Gasket - Oil Filter to Block seals the joint between the oil filter housing and the cylinder block, within the Oil Cooler and Filter assembly. It ...

O-Ring for the oil pump inlet tube, part of the oil pump, sump and filter assembly. It seals the joint at the oil pump inlet (pick-up) tube, keepi...

Front Mudflap Brackets - Black - a pair of stainless steel brackets in a black finish that carry the front mud flaps at the rear of the front wheel...

Fuel Pressure Sensor for the high-pressure fuel injection circuit on petrol engines. It measures fuel rail pressure and temperature and reports to ...

Thermostat Housing - engine cooling circuit component for the 3.0L Ingenium six-cylinder petrol engine (AJ20P6 / AJ22P6). The housing carries the ...

Oil Pump Inlet Tube Assembly for the engine lubrication system. The inlet tube draws oil from the sump and feeds it to the oil pump inlet, forming...

Front Brake Pad Kit - friction pad set for the front disc brake assembly, for the 380 mm front disc and size 20 caliper configuration. The pads lo...

Exhaust Gas Temperature Sensor located at the turbocharger. It measures the exhaust gas temperature entering the turbine and aftertreatment stage a...

Kick Panels - moulded interior trim panels for the footwell area, supplied as a pair. The panels fit against the lower bulkhead on either side of ...

Body Panel Seal for the rear cab, part of the body sealing system. Fitted at the rear cab body panel joint, it seals the panel interface against w...

Turbocharger Oil Return Hose in the turbocharger lubrication circuit. The hose carries oil draining from the turbocharger bearing housing back to ...

Handbrake Pad Set - replacement friction pads for the X-Eng disc handbrake (transmission brake) conversion. The conversion replaces the drum-type ...

Front Brake Pad Set - friction pads for the front disc brake assembly. Each pad is friction material bonded to a steel backing plate. The pads loc...

Rear Brake Disc - a vented disc from the rear brake disc and caliper assembly. The disc is mounted on the rear hub behind the road wheel and rotat...

Primary Timing Chain Tensioner from the timing drive assembly at the front of the 2.0L four-cylinder AJ200 / AJ20P4 engine. The tensioner bears ag...

Timing Chain - Secondary, Upper is part of the camshaft drive of the 2.0L Ingenium four-cylinder petrol engine (AJ200 / AJ20P4), including plug-in ...

Wading Kit for the axle and transmission breather circuit on V8 applications. The axle, gearbox and transfer casings vent to atmosphere through br...