Land Rover Defender Parts

Sealing Washer - copper sealing ring for the cooling system drain points. It seats under the radiator drain plug and the cylinder block drain tap, ...

ATF - Dexron III is an automatic transmission fluid meeting the Dexron III specification, supplied in a 5 litre container. It is a hydraulic fluid...

Stub Axle Bolt is a hex-head retaining screw that secures the front stub axle to the swivel pin housing. The stub axle carries the wheel hub and b...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Headlamp Body with manual headlamp levelling. The headlamp body is the housing and reflector unit that carries the headlamp light unit and mounts ...

Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...

Window Filler Strip is a body weather-sealing trim for the side (quarter) window aperture, closing the gap between the fixed window glass and the s...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Hazard Warning Switch, the 12V illuminated rocker switch located on the lower dash switch panel. When pressed it flashes all four direction indica...

Swivel Pin Housing Kit rebuilds the upper pivot of the front axle swivel housing, where the steering knuckle articulates on the axle. This is the v...

Crankshaft Oil Seal seals the front timing cover where the crankshaft nose passes through it. Fitted to the 2.5L 300 TDi diesel engine, the seal r...

Fuel filter element used within the diesel fuel system to remove particulate contamination and water from fuel prior to delivery to the high-pressu...

Tab Washer locks the drop arm retaining nut on the Adwest power steering box, its tab folded against a flat on the nut to stop it working loose und...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...

Set Screw, M8 x 70 mm. A fully threaded hexagon-head fastener in high-tensile steel with a bright zinc-plated finish. Used across a range of chassi...

Rear Brake Pad Set for the rear disc brakes, part of the hydraulic braking circuit. The pads are clamped against the rear brake disc by the caliper...

Contact Set for the ignition distributor of the 3.5L V8 petrol engine. The contact breaker points open and close the primary circuit to the ignitio...

Track Rod End for the steering linkage, with a left-hand thread. The track rod end forms the ball-jointed connection between the steering link and...

Glass Fuse rated at 5A, a cartridge-type fuse used in the vehicle electrical system. The fuse seats in the fuse box or an inline fuse holder and p...

Rear Wheel Cylinder (Right-Hand) is the hydraulic actuator within the rear drum brake assembly, mounted to the brake backplate. Under pedal pressu...

Oil Temperature Transmitter for the engine instrumentation circuit. The transmitter threads into the oil gallery and varies its electrical resistan...

Nyloc Nut with an M16 thread - a nylon-insert locking nut used on heavily loaded suspension and driveline fixings. A nylon collar set into the top...

Brake Pipe Clip secures and routes rigid brake pipes along the chassis within the braking system, holding them in position and guarding against cha...

Heater Blower Seal sealing the joint between the intake grille and the heater duct, for diesel applications. Fitted in the heater air intake, it cl...

Wiper Delay Relay for the front windscreen wiper circuit, controlling the intermittent (delay) wipe function. It times the pause between wipe cycl...

Water pump gasket Puma 2.4

Front seat belt LH

Camshaft Oil Seal seals the camshaft on the 2.5L 4-cylinder diesel engines, including the 200TDi. Fitted at the front of the engine where the cams...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Used on four-cylinder petrol and diesel engines, including the 200TDi an...

Steering Wheel Boss in the steering column assembly, providing the mounting interface between the column shaft and the steering wheel. The 48-spli...

Carpet Drive Clip is an interior trim fastener used to retain the floor carpets against the body. The drive-clip design presses into a mounting ho...

Gasket for the front cover of the LT67 gearbox. Seals the front cover plate against the front face of the gearbox housing, preventing transmission...

Gasket for the carburettor-to-inlet-manifold joint in the induction system of the 2.25L 4-cylinder petrol engine. The gasket fits between the carb...

Speedo cable oil seal retainer plate

Gear Lever Locating Pin locates and retains the main gear lever within the manual gearbox. It holds the lever against its pivot so that shift move...

Windscreen Hinge Bolt is a fixing used to secure the folding windscreen frame hinge to the scuttle. It clamps the hinge mounting at the base of th...

Exterior Door Handle with Lock Barrel and Keys, left-hand (nearside). The complete locking handle for the front door, comprising the external push...

Accelerator Pedal Return Spring for the cable-operated throttle linkage. The spring returns the accelerator pedal to its rest position when foot p...

Mud Shield for the differential pinion. This pressed shield fits over the differential drive flange, ahead of the pinion oil seal, protecting the ...

Heater control cable clip (Heating / Heater Controls)

Alarm Remote Transmitter, the handset used for remote operation of the vehicle's anti-theft alarm and central locking system. The unit transmits a...

Fan Belt for the engine auxiliary (accessory) drive. Transmits drive from the crankshaft pulley to the water pump, cooling fan and dynamo or altern...

Front Propshaft This propshaft transmits drive from the transfer box output to the front axle differential, forming part of the four-wheel-drive d...

HT Ignition Lead Set for the 2.25L and 2.5L 4-cylinder petrol ignition system. This set of four high tension leads connects the distributor to eac...

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Rear Indicator Lamp for the exterior lighting system, fitted within the rear lamp cluster. It provides the rear directional turn-signal indication...

Front direction indicator lamp assembly used in the exterior lighting system, mounted on the front wing to provide visual signalling for directiona...