Land Rover Defender Parts

Hex-head bolt, 3/8" UNC thread, 1-1/8" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and so...

Power Steering Pump for the 2.5L five-cylinder turbo diesel, supplied as a complete pump assembly. Belt-driven from the engine, the pump draws flu...

Injector Clamp Bolt for the Td5 2.5L 5-cylinder turbo diesel engine. It secures the injector clamp to the cylinder head, holding the fuel injector ...

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Oil Pump Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the oil pump to its mounting on the engine. It clamps the pump body agains...

Centre Silencer Replacement Pipe for the exhaust system, fitting in place of the intermediate (centre) silencer box. The pipe provides a straight-...

Lamp Guard - Round - 73mm - a protective guard that fits over a round 73 mm lamp to shield the lens. It clamps over the light unit to protect the ...

Light Guard Set - Rear Hinged rear lamp guard set that protects the rear lamp lenses from stone strike and low-speed impact during off-road use. T...

Hex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...

Oil Seal for the input shaft of the ZF automatic gearbox. The seal fits at the front of the gearbox, where the torque converter drives the input s...

Lock Nut is a captive plastic fastener (commonly known as a Lokut nut) that receives a No. 10 self-tapping screw. The body pushes into a square pa...

Ignition Switch - Diesel - Switch Only is the electrical switch element of the ignition system for diesel applications. It supplies the rotary swi...

Nut - an M10 self-locking hex nut used in the exhaust system to secure flanged joint and manifold connections. The self-locking feature resists lo...

Oil Pressure Switch monitors pressure in the engine lubrication circuit and signals the instrument gauge and low-pressure warning lamp. Mounts to ...

Self-Locking Nut is an M12 x 1.25 nyloc nut used at the shock absorber mountings in the suspension. It retains the lower mounting of the front and...

Air intake duct hose Def 2.5DT & 200TDi air cleaner to turbocharger

LED Light Upgrade Kit (coloured lens type) - a complete set of WIPAC 73mm LED lamps replacing the original incandescent front and rear exterior lam...

Steering Wheel Nut - the M14 hex retaining nut that secures the steering wheel to the steering column. It clamps the wheel onto the splined upper ...

Bolt 1/4" UNF x 7/8" is a fixing bolt for the track rod and steering damper within the steering linkage. It clamps the track rod end and secures t...

Exhaust Manifold Stud secures the manifold to the cylinder head on the 4-cylinder engine. It threads into the head and carries the manifold flange...

Brake Caliper Repair Kit supplying replacement piston seals for overhauling the brake caliper. New piston seals restore the caliper's ability to r...

Screw – Facia is a No. 6 × 1/2 in self-tapping screw used to secure the facia panel assembly, including the cowl instrument binnacle and the upper ...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Differential Pinion Inner Taper Roller Bearing used in the differential pinion shaft assembly within the axle final drive. The bearing supports th...

Staple Clamp for the soft top canvas hood, part of the rear body tie-down hardware. Fixed to the rear body side, it forms the anchor loop that the...

Rocker Cover Gasket (Top) - seals the rocker cover joint on the 2.6L 6-cylinder petrol engine. Fitted between the rocker cover and the cylinder he...

Glazing Rubber Strip - rubber glazing section supplied by the metre. It beds and seals a fixed glass panel into its body aperture, locating the gla...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Fastener clip

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Water Pump for the 200TDi 2.5L turbo diesel engine, operating in the engine cooling circuit. Belt-driven from the crankshaft, the pump circulates ...

Crankcase breather T-piece with restrictor V8 EFI

Steering Ignition Lock Housing mounted on the steering column, combining the mechanical steering lock with the ignition switch mounting. It mechan...

Headlamp Bezel - black finish. The trim ring that surrounds the 7" round headlamp, retaining the lamp unit in the front panel and finishing the hea...

Brake Pad Set for the rear disc brake assembly, supplied without a wear sensor. The pads are clamped by the rear caliper against the brake disc to...

Auxiliary Drive Belt for the front-end accessory drive system, transmitting drive from the crankshaft pulley to the alternator and other engine anc...

Oil seal

Wheel spacer kit fitted between the wheel hub and road wheel within the wheel mounting assembly. The spacers move the wheel mounting face outward...

Oil Seal for the swivel pin housing on the front axle, sealing against the polished surface of the swivel ball. The seal seats in the rear face of...

Nyloc Nut with an M8 thread - a nylon-insert locking nut used as a self-locking fastener in threaded assemblies. A nylon collar set into the top o...

Cable Clip secures wiring harnesses, breather pipes and similar runs to the body, chassis or panel. It locates in an 8mm mounting hole and holds t...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Fuel Filter & Sedimentor Assembly - Td5

Rear Exhaust Silencer forms the rear section of the exhaust system, downstream of the intermediate pipe. It attenuates exhaust noise before the ga...

Plain Washer - imperial-dimensioned flat washer with an internal diameter of 7/16 inch and an outer diameter of 13/16 inch. Used in general fasten...

Hex-head bolt, 3/8" UNC thread, 3/4" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and sock...

Hex-head bolt, 5/16" UNF thread, 3/4" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socke...

T-Piece is a three-way connector in the windscreen washer fluid circuit. It joins the washer hose into two branches, distributing fluid from the p...