Land Rover Defender Parts

Alloy Wheel from the Maxtrac Blindo range, finished in anthracite. Specifications: Size: 16 x 7 inches Bolt pattern (PCD): 5 x 165 Offset (E...

Tapered Front Bumper is a heavy-duty 5mm steel replacement for the standard front bumper. The tapered profile improves the front approach angle. I...

Tapered Front Bumper is a heavy-duty 5mm steel replacement for the standard front bumper. The tapered profile improves the front approach angle. T...

Enhance your Land Rover Defender's off-road capability with the Terrafirma Swing Away Spare Wheel Carrier, designed for Defender 90 and 110 Station...

Rear Coil Spring replaces the standard rear suspension coil springs and raises ride height by approximately 2" over standard. Supplied as a pair. ...

Winch Bumper - Pro Taper Small Frame is a steel front winch-mounting bumper that replaces the standard front bumper to carry a recovery winch, shap...

Winch Bumper - Pro Taper Small Frame is a steel front winch-mounting bumper that replaces the standard front bumper to carry a recovery winch, supp...

Tubular Front Bumper - a non-winch front bumper for Defenders with air conditioning, replacing the standard front bumper. Constructed from black p...

Tubular Front Bumper - a non-winch front bumper for Defenders without air conditioning, replacing the standard front bumper. Constructed from blac...

Tubular Winch Bumper No a Bar with Air Con 90/110/130 Terra Firma

Front Winch Bumper for Defenders without air conditioning, replacing the front bumper and providing a mounting platform for a recovery winch. The ...

Manifold Stud is an M8 x 65 mm threaded stud that secures the inlet and exhaust manifold to the cylinder head on the four-cylinder petrol engine. ...

Snap Ring for the output shaft of the MT82 six-speed manual gearbox. The ring seats in a groove on the gearbox output shaft and retains the output...

Hex Bolt, grade 8.8, M8 x 20mm. A standard metric hexagon head bolt. Grade 8.8 indicates a tensile strength of 800 MPa and a yield strength of 640...

Synchro Unit - the 1st/2nd gear synchromesh assembly carried on the mainshaft of the LT77 five-speed manual gearbox. The synchro hub is splined to...

Differential Gear Kit is a set of differential gears for the Rover-type axle differential, in the 10-spline configuration. The differential gears ...

Heater Control Assembly for right-hand-drive applications, mounting in the dashboard heater control panel to regulate cabin heating and ventilation...

Gear Kit - R380 - 3rd/4th Mainshaft

Power Steering Box - recirculating-ball steering gear of the Adwest Lightweight type, forming the core of the hydraulically assisted steering circu...

Water Pump for the engine cooling circuit, belt-driven from the front of the engine. The pump circulates coolant through the cylinder block, heads...

Rear Tailpipe Silencer is the rearmost section of the exhaust system, combining the final silencer box and tailpipe. It attenuates exhaust gas pul...

Front Brake Hose is the flexible hydraulic hose in the front braking circuit, connecting the rigid brake line on the chassis to the front brake cal...

Bolt used in multiple assembly applications including towing equipment, engine mounting, front stabilizer bar, ACE system, and seat belt anchorage.

Hex Nut

Front Outer Wing is the left-hand (nearside) bolt-on steel body panel covering the front wheelarch and running back from the headlamp panel to the ...

Front Outer Wing is the right-hand (offside) bolt-on steel body panel covering the front wheelarch and running back from the headlamp panel to the ...

Sealing Washer - bonded (Dowty-type) seal for the power steering pump banjo union. The washer is a metal outer ring with a vulcanised elastomeric ...

Banjo Union - the hollow banjo bolt that secures the high-pressure feed hose to the power steering pump outlet. It passes through the eye of the h...

Startermotor 2,5 diesel NEW

Circlip for the front driveshaft CV joint on Defender models to 1993. This circlip retains the CV joint on the front driveshaft, securing it withi...

Piston Ring Set for a single piston, in 0.020-inch oversize. The set provides the compression and oil-control rings for one piston and is machined...

Piston Ring Set for the 2.5 litre four-cylinder naturally aspirated diesel engine, standard bore size. The rings seal the combustion chamber again...

Fitment: All models to 1978 (axle) suffix A All models to (axle) suffix B

Steering Box Race Bearing for the worm and valve assembly of the Adwest power-steering box. The race carries the worm shaft within the recirculati...

Heater Blower Motor Assembly for right-hand-drive vehicles, part of the heater and cabin ventilation system. The blower motor drives the fan that ...

Piston Ring Set for the 2.25L 4-cylinder petrol engine, in +0.060 in oversize. Piston rings perform three functions at once: they seal the combust...

Piston Ring Set for the 2.25L 4-cylinder petrol engine, ground to +0.030" (0.76mm) oversize for use with rebored cylinder bores. The rings seal th...

Carburettor Conversion Kit for the fuel system of the 2.25L four-cylinder petrol engine built to Detox (EGR) emission-control specification. The k...

Bearing layshaft LT95 4-speed manual gearbox for Rover 3.5L V8 - S3 109" Stage One V8 - early 110" V8 (Stage Two) - 101" Forward Control - Classic...

Power Steering Reservoir Cap - the sealing cap for the power steering fluid reservoir, part of the steering hydraulic circuit. It closes the top of...

Mainshaft Bearing for the LT77 five-speed manual gearbox. This tapered roller bearing supports the gearbox mainshaft, locating it within the gearb...

Circlip - Mainshaft Bearing Housing for the Land Rover Series I, II, and III gearbox. This circlip retains the mainshaft bearing within the bearing...

Main bearing set for the three-bearing 2.25L four-cylinder engine, forming the crankshaft support in the cylinder block bottom end. The shells loc...

Cork Washer for the auxiliary (extra) fuel tank in the fuel system. The cork washer forms a fuel-resistant seal at a tank fitting, compressing on ...

R-Clip - spring steel retaining clip for the centre pin of the military (NATO) pattern front bumper, part of the front bumper and towing pin fixing...

Spring Helper Retaining Plate - 130