Land Rover Defender Parts

Hand Throttle Grommet fits into the hand throttle control assembly, lining the aperture where the throttle cable passes through and sealing it agai...

Exhaust Clamp Plate for the front exhaust pipe mounting. The plate clamps the front section of the exhaust at its mounting point, holding the pipe...

PAS Hose - Reservoir to Pump is the low-pressure supply hose in the power-assisted steering hydraulic circuit, running from the fluid reservoir to ...

Bottom Radiator Hose in the engine cooling circuit, running between the lower hose connector on the engine and the radiator bottom connection. Mou...

Coolant Hose for the engine cooling circuit of the 2.5L Naturally Aspirated Diesel engine. This hose carries coolant between the engine block and ...

Galvanised Chassis - complete replacement chassis frame for 88" short-wheelbase vehicles. Fully galvanised as standard, giving corrosion protectio...

Chassis - 109" Station Wagon - Galvanised is a full replacement chassis frame for the long-wheelbase Station Wagon. The galvanised finish provides...

Accelerator Cable Dutch Lightweight Diesel

Front exhaust downpipe, right-hand side, for the V8 exhaust system. The downpipe bolts to the right-hand exhaust manifold flange and carries the e...

Tow Hitch - NATO Pintle is a rotating military-pattern towing hook that mounts directly through the rear crossmember. The pintle rotates to allow ...

Rear Corner Capping - left-hand, galvanised - for the Defender body structure. This pressed steel panel covers the upper rear corner of the body, ...

Adhesive Tape self-adhesive front exterior decal, 23 cm in length. Applied to the front bodywork as the front-position decal strip.

Seat Belt Assembly Rear Centre Lap

Glazing Strip

Body Side Sliding Window is a glazed sliding window assembly for the left-hand body side, comprising the glass panes in their frame. The panes sli...

Door Lock Link is the connecting rod within the front door latch mechanism that couples the inner door handle to the latch locking action, transfer...

Seat Mounting Bracket is the structural mounting point that locates and supports the rear forward-facing split seat, securing the seat base to the ...

Door Check Strap Channel is the channel of the front door check strap (checker) assembly. It guides and retains the check strap as the door swings,...

Windscreen hinge for the right-hand side. One of the pair of hinge brackets that carry the windscreen frame at its lower corners, bolting the frame...

Screw used as a fixing throughout the door hardware assemblies. Four secure the front door latch mechanism; the same screw is specified for the rea...

Clip

Window Regulator - the lift mechanism that raises and lowers the rear side door glass. It mounts inside the door and carries the glass in a guide c...

Nut Plate - captive fixing plate used at the rear body upper mountings. The plate holds the nut captive behind a blind or closed panel section, so...

Fastener Trim Nail used to secure seat trim panels to the seat frame on Land Rover Defender front and centre seat assemblies. This push-fit trim p...

Side Window Sliding Catch - RH is the latch that secures the right-hand sliding side window pane in position. Fitted to the sliding glass, it lock...

Rear Side Door Glass - fixed glazing panel for the rear side door, formed from 5mm clear (untinted) toughened automotive safety glass. It sits wit...

Rear Seat Bracket outer left-hand mounting bracket for the rear seating, securing a forward-facing individual rear seat to the floor. Locates the ...

Facia Grab Handle - the front passenger grab handle that mounts to the upper facia rail across the top of the dashboard. Provides a hand-hold for ...

Sun Visor is the pivoting padded screen at the top of the windscreen aperture, hinged from the header rail to shield the occupant from glare and sw...

Soft Top Drain Channel Spring for the soft top header rail and drain channel assembly. The spring tensions the soft top against the header rail, h...

Mudflap Stiffener Bracket for the front mudflap assembly. The bracket mounts behind the front mudflap to hold it rigid and maintain its shape, pre...

Fuel Injector for the Td5 2.5L 5-cylinder turbo diesel engine. The Td5 uses electronic unit injectors, one per cylinder, seated in the cylinder hea...

Rocksliders Barbarian - Defender 130

Sill Protector is an aluminium protective panel for the body sill (rocker) beneath the doors. It fits over the sill to shield it from stone chips,...

Rear coil spring seat for the chassis, the upper seat that locates and supports the top of the rear coil spring at the chassis outrigger. The seat...

Outer Wing - left-hand front outer body panel. The outer wing forms the visible outer skin over the front wheel arch and locates against the front ...

Rear Axle Coil Spring Mount Bracket - weld-on bracket forming the coil spring mounting on the rear axle casing. The bracket provides the seat and ...

Differential Cover is the pressed plate that closes the differential aperture in the axle casing, retaining the axle oil and giving access to the c...

Front Wing Protector - Rear is an exterior body protection panel fitted to the rear section of the front wing, shielding the panel from stone chips...