Land Rover Defender Parts

Alternator Belt for the 2.5L four-cylinder petrol engine. This drive belt runs from the crankshaft pulley to the alternator, turning the alternator...

Crankshaft - 3-Bearing

Bolt with a 5/16" UNF thread and a shank length of 2-3/4 inches. A standard-thread fastener used in assembly of the four-cylinder engine. Applies ...

Front Exhaust Pipe for petrol applications. This is the front section of the exhaust system, carrying gases from the exhaust manifold rearward to t...

Wiper Motor Shaft & Gear is the internal drive shaft and gear for the central windscreen wiper motor, providing a 120-degree sweep. It transmi...

Number Plate Lamp Plinth is the mounting base for the rear number plate lamp, fixing the lamp unit to the bodywork above the number plate. It loca...

Blanking Plug is a rubber grommet used to seal unused 1-inch (25.4 mm) diameter holes in body panels, bulkheads and floor sections. The plug press...

Rear Sill for the left-hand side, in the high cab body configuration. The sill is the structural panel running along the lower edge of the body be...

Two-Man Bench Seat Cushion for the rear inward-facing bench seat. This is the fixed rear bench cushion that forms the seating surface of the two-s...

Stekker 7-polig Pvc

Rear Leaf Spring - heavy-duty rear leaf spring for the passenger side, built with eight leaves for increased load capacity. Locates the rear axle ...

Leaf Spring Heavy Duty

Spring Road Front SWB 9lf DS

Cone Bearing - Swivel Housing for the front axle swivel pin assembly. Sits within the swivel housing to support the swivel pin on early Series Lan...

Mudshield Output Shaft

Use 251323

Woodruff Key - Camshaft Chainwheel for the 4-cylinder engine timing assembly. This Woodruff key locates the camshaft chainwheel on the camshaft no...

Core Plug - 1-3/8 in. diameter, threaded - for the Series engine block. This threaded plug seals a casting aperture in the engine block, retaining...

Flexible Brake Hose - hydraulic hose carrying brake fluid from the rigid chassis or axle pipe to the wheel cylinder. Forms the flexible link acros...

Gear Lever Bracket - mounting bracket for the gear change lever on the LT76 gearbox. The gear lever pivots in the bracket, locating the lever over...

Transfer Box Gear - High is the high range gear wheel in the Land Rover Series transfer box assembly, fitting Series vehicles from 1948 to 1984. T...

External Circlip - retaining circlip fitted within the LT67 main gearbox. Seats in a shaft groove to axially locate a gear, bearing or spacer on i...

Air Suspension Compressor - AMK-type compressor assembly from the air suspension supply circuit, for vehicles with four-corner air suspension. The...

Front Brake Disc, 363mm diameter, ventilated construction, supplied singly. The disc runs within the front caliper and provides both the friction ...

Brake Pad Set - Rear - friction pad set for the rear brake discs and calipers assembly, supplied as a complete axle set covering both rear wheels. ...

Pump - Water Hepu

Valve - Control

Bolt - a structural fastener used at chassis and front suspension mounting points, including the front cross member and stabiliser bar crossmember,...

M16 Nut for the front suspension arm. Secures a front suspension arm mounting fastener, holding the joint under suspension loads.

Nut - Flag Type

Bolt

Suspension Arm Bolt secures a front suspension arm to its mounting on the chassis/subframe, part of the front suspension arm mounting hardware. Th...

Raised Air Intake relocates the engine's induction intake point from the inner wing up to roof-line height, drawing intake air from above the bonne...

Alloy Expedition Roof Rack for the Land Rover Defender 90. This aluminium alloy roof rack measures 1.8 x 1.4 m and weighs approximately 35 kg. A c...

torx screw and washer, M6x18mm OEM

Steel Wheel - a 20x8 modular steel road wheel finished in satin black, supplied with matching wheel nuts. Rim specification: 20x8 in, ET45 offset,...

Turbocharger Gasket for the 2.0L AJ200D Ingenium four-cylinder diesel, sealing the turbocharger mounting joint against exhaust gas leakage. The ga...

Brake Pad Set - Front - friction pad set for the front brake discs and calipers assembly, supplied as a complete axle set covering both front wheel...

Front Brake Disc - a vented disc from the front brake disc and caliper assembly. The disc is mounted on the front hub behind the road wheel and ro...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Fuel Tank Sender Unit for the Defender 90 main fuel tank. The sender unit mounts inside the fuel tank and uses a float arm and variable resistor t...

Front Brake Pads Britpartxs

Oil Filter for the engine lubrication system. It removes contaminants from the engine oil as it circulates, protecting the bearings and moving par...

Washer - a sealing washer for the air conditioning system, used at the condenser and compressor refrigerant connections. It seats at the pipe unio...

Spare Wheel Cover is a rigid cover that fits over an externally mounted spare wheel. Moulded in hard plastic with a gloss black finish, it shields...

Synthetic Winch Rope - 10mm x 24m - 10,000 lbs for 4x4 winch recovery. This synthetic fibre winch rope is rated to 10,000 lbs (approx. 4,536 kg) b...