Land Rover Defender Parts

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Oil Drain Plug threads into the drain port at the base of the engine sump, sealing the oil pan against leakage during operation. It sits within the...

Nut for U-bolt M12

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Locking Flange Nut - M8 for fastening applications requiring vibration-resistant fixings. A prevailing-torque hexagonal nut with an integral flang...

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

ATF - Dexron III is an automatic transmission fluid meeting the Dexron III specification, supplied in a 5 litre container. It is a hydraulic fluid...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Panhard Rod Bolt with a 1/2" UNF (Unified National Fine) imperial thread and a 3-1/4" shank length, manufactured to a high-tensile grade. Secures ...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Relay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...

Fuel return tube O-ring seal

Diesel Exhaust Fluid (AdBlue) is a consumable fluid for the Selective Catalytic Reduction (SCR) exhaust aftertreatment system on diesel engines. I...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Oil filter element for the engine lubrication system within the Oil Cooler and Filter assembly. This cartridge-type element removes particulate c...

Steering Column Bolt for the lower steering shaft coupling. This pinch bolt clamps the lower steering shaft to its mating joint, securing the colum...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Air Suspension Connector joins the valve block to a high-pressure air line within the air suspension pneumatic circuit. The fitting forms a sealed...

Hub Nut - M24 x 2.0 for wheel hub and bearing retention. This M24 x 2.0 metric hub nut secures the wheel hub or halfshaft flange onto the stub axl...

Exhaust Stud Nut for front exhaust system connections. This nut secures exhaust pipe sections to the manifold or downpipe studs, maintaining a gas...

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

Magnetic Oil Drain Plug for the engine oil sump on the 2.0L Ingenium (AJ200/AJ20) four-cylinder petrol and diesel engines. The plug seals the drai...

Rear Crankshaft Oil Seal for the 2.0L AJ200-series four-cylinder engine, in both petrol and diesel applications. Seals the rear of the crankshaft ...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Valve - Control

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...

Accessory Drive Idler Pulley

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

Cover Gasket for the crankcase cover, part of the emission-control and crankcase ventilation system on the 2.0L AJ200 four-cylinder diesel engine. ...

EGR Outlet Gasket for the 2.0L four-cylinder diesel engine (AJ200), sealing the joint where the EGR valve outlet meets the inlet manifold. It main...

Idler Pulley for the front-end accessory belt drive, 90mm diameter. The idler routes and guides the auxiliary drive belt around the accessory pull...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Cylinder Head Gasket for the 5.0L V8 AJ133 petrol engine. The gasket seals the joint between a cylinder head and the engine block, containing comb...