Land Rover Defender Parts

Bonnet Hinge Bush for the Land Rover bonnet hinge assembly. This bush fits into the bore of the bonnet hinge, providing a wear surface around the ...

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Oil Filter: a cartridge-type engine oil filter for the engine lubrication circuit. It removes contaminants from the engine oil and should be replac...

Swivel Housing Grease for the front axle swivel assembly, supplied as a single pre-measured one-shot sachet. The sachet delivers the correct charg...

Body Panel Locknut for square-hole panel apertures, used in body, interior, and trim panel assemblies. This push-fit captive nut locates into a sq...

Nyloc Nut with a 3/8" UNF thread, used to secure propshaft flange bolts. A nylon insert set into the crown of the nut deforms over the bolt thread...

Sump Gasket - 4-Cyl for the engine sump sealing joint on Land Rover 4-cylinder engines. This gasket seals the mating face between the sump pan and...

Sump Plug Washer - copper sealing washer for the sump drain plug and thermostat housing on petrol and early diesel engines. The copper washer seat...

Rocker Cover Gasket - Diesel for the 2.25L and 2.5L 4-Cylinder diesel engine. This gasket seals the joint between the rocker cover and the cylinde...

Brake Drum Screw for the brake drum assembly. This retainer screw secures the brake drum to the wheel hub flange, preventing the drum from displac...

Clutch Slave Cylinder is the hydraulic actuator in the clutch release circuit, mounted externally on the gearbox bellhousing. When the clutch peda...

Propshaft Bolt - a fastener that secures the propshaft universal-joint flange to the differential drive flange within the driveline. It clamps the...

Rear Light Lens for the rear stop and tail lamp. The red lens fits over the lamp body to cover the stop and tail bulb, transmitting the brake ligh...

Hub Cap fits over the end of the front or rear hub, enclosing the drive flange and hub assembly. It closes off the outer end of the hub to retain ...

Rocker Cover Gasket seals the joint between the rocker (valve) cover and the cylinder head at the top of the engine, within the valvetrain assembly...

Door Mirror supplied as a complete unit comprising the mirror head and its mounting arm, for external door mounting to give rearward visibility fro...

Spiralok Nut for body panel and interior trim fixings. This spring-steel speed nut (clip nut) clips to a panel flange or through a mounting hole a...

Side Lamp - front side (parking) lamp in the exterior lighting system. Dome-type front side lamp providing position and marker lighting at the fro...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Oil Filter for the engine lubrication system of the 2.25L four-cylinder petrol and diesel engine. The filter traps combustion by-products, metal p...

clutch master cylinder OEM Delphi

Hub Bearing - a tapered roller bearing for the front and rear axle wheel ends. It supports the rotating wheel hub on the stationary stub axle, carr...

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Indicator Lamp Lens, amber, for the round-type direction indicator (turn signal) lamp. The lens fits over the lamp body to seal and protect the bul...

Sump Plug Sealing Washer for the engine lubrication system. It seats between the oil drain plug and the sump pan boss, sealing the joint so the plu...

Oil Filter: a cartridge-type engine oil filter for the engine lubrication circuit. It removes contaminants from the engine oil and should be replac...

Floor Panel Screw with a mushroom head profile, used to secure floor plates and lower rear body panel assemblies on the Defender. The low-profile ...

Clutch Master Cylinder Copper Washer for the hydraulic clutch system. Copper sealing washer used at the adaptor connection between the clutch hydr...

Front Cover Oil Seal

Thermostat Housing Gasket in the engine cooling system. This gasket seals the thermostat housing to its mating surface on the engine, preventing c...

Fan Belt for the engine auxiliary (accessory) drive. Transmits drive from the crankshaft pulley to the water pump, cooling fan and dynamo or altern...

Number Plate Lamp for the rear number plate lighting circuit. This complete lamp assembly mounts at the rear of the vehicle to illuminate the numb...

Thermostat Housing Gasket for the engine cooling system. This top gasket seals the joint between the thermostat housing and the engine, preventing...

Clutch Release Bearing installed within the Clutch & Flywheel Assembly, operating between the clutch release fork and the clutch cover diaphrag...

Manifold Gasket for the 2.25L and 2.5L 4-cylinder petrol engines. This gasket seals the combined inlet and exhaust manifold assembly to the cylind...

Nyloc Nut with a 1/2" UNF thread, used to retain suspension and steering ball-joint fixings. A nylon insert set into the crown of the nut deforms ...

Radiator Cap seals the radiator filler neck and maintains the engine cooling circuit at its rated pressure. Rated at 9 lb (0.62 bar), the spring-l...

Hub Nut Spanner for the front hub and wheel bearing assembly. The 52mm tool engages the hub retaining nut on the front stub axle. Designed for use...

Engine Mounting is a rubber-to-metal anti-vibration mount in the engine mounting assembly, supporting the petrol engine on the chassis frame. The ...

Brake Pipe Union for the hydraulic brake system, a male fitting in brass. This union connects a 3/16 inch brake pipe into the brake hydraulic circ...

Brake & Clutch Pedal Pad for the foot pedal assembly. This moulded rubber pad fits over the brake and clutch pedal arm, providing the grip surf...

Dash Ventilator Bulkhead Seal for the fresh air intake assembly. Fitted between the dash ventilator panel and the bulkhead, the seal forms an air-...

Hex Nut - 5/16" UNF is a plain hexagonal nut with a 5/16 inch UNF thread, used as a general-purpose imperial-thread fastener throughout the chassis...

Stop/Tail Lamp Assembly for the rear lighting circuit, combining the tail (running) light and stop (brake) light in a single unit. The assembly mo...

Oil Filter: a cartridge-type engine oil filter for the engine lubrication circuit. It removes contaminants from the engine oil and should be replac...

Side Lamp Lens - Front - Clear is the replaceable lens for the front side and indicator lamp within the exterior lighting assembly. The clear lens...

Clutch Pedal Box Top Gasket for the clutch pedal housing on manual transmission vehicles. This gasket seals the joint between the clutch pedal box...