Land Rover Defender Parts

Dipstick Tube for the engine lubrication system on non-V8 four- and six-cylinder engines. The tube fits into the cylinder block and guides the oil ...

O-Ring for the LT95 combined gearbox and transfer box. It seals one of the shaft and housing joints within the unit, retaining gear oil and prevent...

Grommet - rubber blanking grommet for the transmission (gearbox) tunnel cover. This rubber grommet seals the access aperture in the gearbox tunnel...

Vent Lid Hinge Pin - hinge pin for the dash ventilator flap. This pin forms the pivot on which the dash fresh-air ventilator lid hinges, allowing ...

Lock Washer secures a threaded fastener against loosening under vibration and thermal cycling. Fitted beneath the nut or bolt head, it bites into ...

Flywheel Housing Stud - a mounting stud at the flywheel housing. Threaded into the housing, it provides the fixed stud onto which the mating compo...

Front Halfshaft Bearing - roller bearing supporting the inner end of the front halfshaft within the front axle housing. Located at the inboard end...

Lamp Guard Distance Piece - spacer for lamp guard mounting hardware. The distance piece fits between the lamp guard frame and the light body or mo...

Spring Clip - a retaining clip in the transfer gearbox selector linkage. It secures the transfer lever to its pivot, holding the gear-change lever...

Plain Washer - the upper mounting washer for the shock absorber. It seats over the top shock absorber mounting stud beneath the retaining nut, spr...

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Head Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...

Door Hinge - left-hand door hinge that mounts the side door to the body hinge pillar and carries the door as it swings. Steel hinge for the front ...

Door Hinge - right-hand door hinge that mounts the side door to the body hinge pillar and carries the door as it swings. Steel hinge for the front...

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Drive Flange & Mudshield Kit for the Salisbury rear axle. The drive flange bolts to the rear hub and couples the axle half-shaft to the hub, t...

Hex-head bolt, 5/16" UNF thread, 1" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and sockets...

Water Pump for the 2.25L 4-cylinder engine, operating in the engine cooling circuit. Belt-driven from the crankshaft pulley, the pump circulates c...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Castle Nut - M12 castellated nut used on the steering and suspension ball-joint fixings. Its slotted crown takes a split pin through the drilled h...

Head Gasket Seals the cylinder head to the cylinder block on the pre-TDi 2.25L and 2.5L naturally aspirated and turbocharged diesel engines. It co...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Blind Spot Mirror head for the left-hand door: a complete replacement mirror head with an integrated wide-angle convex section. The head measures ...

Headlamp Assembly for the front exterior lighting system, supplied as a pair. Each crystal-style halogen unit mounts in the front lighting housing...

Spare Wheel Cover in black vinyl, sized to fit a 235/85 R16 spare tyre. The cover fits over an externally mounted spare wheel to shield the tyre a...

Heater Hose carries engine coolant between the valve and the heater tap, forming part of the heater coolant circuit that feeds the heater matrix. ...

Inlet Manifold Stud with a UNF thread. Threads into the cylinder head to mount the inlet manifold, taking the manifold nut that clamps the manifol...

Shock Absorber Bush - Polyurethane is a polyurethane mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chas...

Heater Control Finger Grip The finger grip fitted to a heater control slider on the heater (HVAC) control panel, operated in the up/down plane. It...

Barrel Lock with Key A lock barrel (cylinder) supplied complete with its key, forming the keyed locking element of the door lock assembly. The bar...

Mounting Stud

Hexagon Nut with a 7/16" BSF (British Standard Fine) thread. A standard nut cut to the British Standard Fine thread form used throughout the fixin...

Wheel Cylinder Repair Kit A seal repair kit for overhauling the rear brake wheel cylinders, part of the drum braking system. The wheel cylinder si...

Steering Box Joint Washer - 0.005" selective shim washer used within the steering box. Fitted at the steering box joint face, this shim sets the c...

Radiator Cap Pressure-relief filler cap for the engine cooling system, sealing the radiator or coolant expansion tank filler neck. Rated to releas...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Lokut Nut is a self-locking nut used to secure the headlamp to the body at the front wing. The self-locking design resists loosening under vibrati...

LED Light Kit - 73mm

Reverse Lamp with a clear lens and LED illumination, forming part of the rear lighting assembly, providing white light to the area behind the vehic...

Halfshaft Collar is a locating collar fitted to the front axle halfshaft. It seats against the inner side of the halfshaft bearing (244150), setti...

Seat Belt Buckle - Right-Hand - the latching receptacle of the seat belt restraint, into which the belt tongue (latch plate) engages and locks to h...

Plain Washer - a flat, load-spreading washer with a 1/4 in (6 mm) bore and 5/8 in outside diameter, approximately 1/16 in thick, finished in Sherar...

Heater (Glow) Plug Ballast Resistor for the diesel pre-heat circuit. Wired in series with the heater plugs, the resistor drops the battery supply t...

Bolt, a hexagon-head fastener with a 5/16" UNF thread, 7/8" long. This imperial fastener is of the UNF (Unified National Fine) thread series and i...

Spring plate

Handbrake Locking Plate for the rod-operated transmission handbrake - the drum-type parking brake mounted at the transfer gearbox output. The plat...