Land Rover Discovery Parts

Brake Disc for the rear axle. This disc is the rotor that the rear caliper clamps to slow the wheel. Sized for the 20-inch brake disc and caliper ...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Brake Hose - Rear - LH - With Bracket is a flexible hydraulic hose in the rear brake circuit, fitted on the left-hand side. It carries brake fluid...

External Torx Head Bolt, M8 x 48 mm, for the front propshaft flange. The bolt clamps the front propshaft flange to its mating drive flange. Its ex...

Connection - Water Outlet

Bearing - Wheel Hub

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Oil Filter Element and Seal

Water Pump is the engine-driven mechanical pump that circulates coolant through the cylinder block, cylinder heads and radiator to maintain engine ...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Relay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...

Wheel Bearing Kit

Brake Disc for the rear axle. This disc is the rotor that the rear caliper clamps to slow the wheel. Sized for the 20-inch brake disc and caliper ...

Bolt

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Valve Stem Seal seals the point where the valve stem passes through the cylinder head valve guide, controlling the oil reaching the stem and preven...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

Lazer ST4 Evolution LED Spotlight - a compact four-LED auxiliary driving lamp producing a controlled long-range beam for forward illumination. The...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on modern vehicles equipped ...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on selected vehicles utilizi...

Front Suspension Arm Bush - Inner Mount - the rubber-bonded pivot bush at the inner mounting point of the front suspension arm, within the front su...

Rear Crankshaft Oil Seal Fitting Tool guides and aligns the rear main crankshaft oil seal into its housing during engine rebuild work, part of the ...

Wheel Bearing - Rear, a component of the rear hub assembly. The rear wheel bearing carries the vehicle's rear load and allows the road wheel and h...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Idler Pulley for the accessory drive belt system of the 2.0L I4 Ingenium (AJ200 / AJ20) petrol and diesel engine. The idler pulley guides the rout...

Drive Belt Tensioner for the accessory drive belt system of the 2.0L I4 Ingenium (AJ200 / AJ20) petrol and diesel engine. This is a double belt te...

Plug cooling system bleed

Front Suspension Arm Bush - the rubber-bonded pivot bush that mounts the front suspension arm to the subframe, within the front suspension arm asse...

Front Strut Boot Kit renews the protective gaiter and mounting hardware for a front air suspension strut, part of the four-corner air suspension sy...

Battery - 12V lead-acid battery of flooded, non-spillable construction, for the vehicle low-voltage electrical supply. Non-spillable construction ...

Timing Chain Kit for the valve timing drive of the Ingenium 2.0L 4-cylinder diesel engine (AJ200 series). The timing chain drive synchronises cran...

Spark Plug Well Gasket seals the spark plug aperture in the camshaft (valve) cover on the right-hand cylinder head bank. It prevents engine oil fr...

Air Suspension Compressor - AMK-type compressor assembly from the air suspension supply circuit, for vehicles with four-corner air suspension. The...

Wheel Bearing Circlip - 51 mm retaining ring for the wheel hub bearing. Seats in the groove of the knuckle bore and locates the hub bearing axiall...

Coolant Tube forming the primary coolant path between the cylinder block and the water outlet. This aluminium tube carries coolant from the engine...

Water Pump is the engine-driven mechanical pump that circulates coolant through the cylinder block, cylinder heads and radiator to maintain engine ...

Front Brake Disc, 363mm diameter, ventilated construction, supplied singly. The disc runs within the front caliper and provides both the friction ...

Brake Hose - Rear - LH - With Bracket is a flexible hydraulic hose in the rear brake circuit, fitted on the left-hand side. It carries brake fluid...

Brake Pad Set - Rear - friction pad set for the rear brake discs and calipers assembly, supplied as a complete axle set covering both rear wheels. ...

Hub Bearing

Dust Cap for a brake bleed nipple. This small protective cover fits over the bleed screw on a brake caliper or wheel cylinder. It keeps dirt and m...

Oil Filter for the engine lubrication system. It removes contaminants from the engine oil as it circulates, protecting the bearings and moving par...

Oil Filter - the replaceable cartridge element for the engine lubrication circuit, fitted inside the filter housing on the oil pump, cooler and fil...