Land Rover Discovery Parts

Side Repeater Lens is the lens cover for the side repeater indicator lamp. It fits over the repeater lamp bulb to seal the unit and colour the emi...

Kit latch bonnet catch LHD

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Drain plug

Fuel Filler Cap that seals the fuel tank filler neck. Non-locking type with a black finish, closing the filler neck against fuel vapour loss and t...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Brake Disc, front, vented. Part of the front braking system. The disc mounts to the front wheel hub and rotates with the wheel; the brake caliper ...

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Oil Pressure Switch monitors pressure in the engine lubrication circuit and signals the instrument gauge and low-pressure warning lamp. Mounts to ...

Fir Tree Fastener push-in fixing in light grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fi...

Fuel Return Check Valve is a non-return valve fitted in the fuel return circuit of the Td5 fuel system. It permits fuel flow in one direction only...

Brake Pipe Clip (double) used to route and secure rigid brake pipes within the braking hydraulic system. The double form retains two brake pipes s...

Turret Fitting Kit, galvanised: a pair of standard-height front shock absorber turrets supplied with fitting hardware. The turrets are made from g...

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Injector Clamp Bolt for the Td5 2.5L 5-cylinder turbo diesel engine. It secures the injector clamp to the cylinder head, holding the fuel injector ...

Stud M8 x 25

Bolt - Bracket to Chassis is an M10 x 60 mm fastener that secures a bracket to the vehicle chassis frame. It has a 10 mm nominal thread diameter a...

Wheel Centre Cap with a pewter finish, fitting the centre bore of the alloy road wheel. It conceals the hub and the wheel fixings at the centre of ...

Transfer Box Hi/Lo Switch is a position switch fitted to the LT230 transfer box. It belongs to the transfer box and four-wheel-drive control circui...

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Thermostat Housing Gasket for the 200TDi 2.5L turbo-diesel engine, sealing the thermostat housing to the cylinder head within the engine cooling ci...

Timing Cover Mudshield is the pressed shield that fits over the timing cover at the front of the engine. It screens the timing case and front pull...

O-Ring for the power steering hydraulic circuit, sealing a union on the 6mm power steering pipe. The O-ring seats at the connection between the po...

Oil seal

Strap

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Flame Trap fits into the crankcase ventilation circuit of the V8 twin-carburettor petrol engine, between the crankcase breather and the carburettor...

Grommet

Rubber Plug Cushion is a moulded rubber blanking plug that fits into a pre-formed aperture in the body, frame or seat base to close off the opening...

Inline Fuel Filter for petrol fuel-injection (EFI) systems, fitted in the pressurised fuel supply line between the fuel pump and the injector rail....

Alternator, 120A, for the 2.5L Td5 diesel - the charging-system unit that supplies the vehicle's electrical power and recharges the battery. Belt-...

Drive Belt Idler Pulley for the auxiliary (accessory) belt drive of the Td5 2.5L 5-cylinder turbo diesel engine. The pulley mounts above the water...

Flywheel Housing Gasket for the 200 TDi diesel engine, sealing the joint between the flywheel (or drive plate) housing and the rear face of the cra...

Brake Caliper Repair Kit supplying replacement piston seals for overhauling the brake caliper. New piston seals restore the caliper's ability to r...

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Handbrake Spring Kit for the transmission brake – the drum-type parking brake mounted at the transfer box output. The kit comprises the shoe reten...

Hex-head bolt, 3/8" UNC thread, 1-1/8" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and so...

Hex-head bolt, 5/16" UNC thread, 1" long. Unified Coarse (UNC) thread form with a hexagonal head for use with standard imperial spanners and socke...

Oil Seal for the input shaft of the ZF automatic gearbox. The seal fits at the front of the gearbox, where the torque converter drives the input s...

Nut - an M10 self-locking hex nut used in the exhaust system to secure flanged joint and manifold connections. The self-locking feature resists lo...

Self-Locking Nut is an M12 x 1.25 nyloc nut used at the shock absorber mountings in the suspension. It retains the lower mounting of the front and...

Oil Pump Bolt for the Td5 2.5L 5-cylinder turbo diesel engine, securing the oil pump to its mounting on the engine. It clamps the pump body agains...

Radius Arm Washer is a plain washer used at the radius arm mounting in the suspension. It seats under the radius arm fastener to distribute clampi...

Front Drive Shaft, left-hand, part of the front axle drive assembly. The shaft transmits torque from the front differential to the front wheel hub...

Static Lap Seat Belt for the second-row seating position, forming part of the interior occupant restraint system. The non-retractable, fixed-lengt...

Exhaust Olive for the exhaust system. This tapered sealing ring fits into the slip joint between two exhaust pipe sections. As the joint clamp is ...