Land Rover Discovery Parts

Oil Filter Rotor is the rotating element of the centrifugal oil filter on the Td5 2.5L 5-cylinder turbo diesel engine. Mounted within the centrifu...

Rear Reflector mounts in the rear lamp area as part of the rear lighting and signalling assembly. A passive retroreflector that returns incident l...

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Engine Mounting - bonded rubber-to-metal mount within the engine mounting assembly of 4-cylinder Land Rover engines. It locates between the engine...

Accelerator Pedal Pad - a moulded rubber pad fitted over the accelerator pedal arm, providing a textured grip surface for the driver's foot and pro...

Shock Absorber Bush is a rubber mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chassis and axle attachme...

Fuel Tank Sender Locking Ring for the fuel tank sender unit assembly. This ring secures the fuel level sender unit in position within the fuel tan...

Oil Filter for the Td5 2.5L five-cylinder turbo diesel. Part of the engine lubrication system. The filter is a replaceable cartridge element that ...

Spring Retainer Ring for the front coil spring on the suspension. The ring secures the coil spring to its seat, holding the spring captive so that...

Fuel Lift Pump for the low-pressure fuel supply circuit of the 2.5L 300TDi turbo diesel engine. This engine-mounted mechanical diaphragm pump draw...

Exhaust Manifold Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. Seals the joint between the exhaust manifold and the cylinder head, preve...

Fuel Injector Harness for the Td5 fuel injection system, carrying the electrical connection between the engine wiring loom and the electronic unit ...

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Tap screw

Drive flange for the front axle drive shaft hub assembly. This component provides the splined connection between the drive shaft and the wheel hub,...

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Clutch Release Staple is the spring retaining clip that secures the clutch release bearing assembly to the clutch fork, holding the bearing in posi...

Cam Cover Gasket - Td5 - Late Type

Oil seal designed to retain lubricant and prevent contamination at the stub axle interface. The seal fits into the stub axle and forms a barrier b...

Front Cover Oil Seal

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Fulcrum Bracket and Ball Joint Assembly for the rear A-frame (top link). The bracket forms the apex of the A-frame and bolts to the rear axle; the ...

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Radius Arm Bush - Rear, Lower - the compliant mount at the lower link of the rear radius arm, between the arm and its chassis bracket. The rear ra...

Exhaust Gasket for the front exhaust section on 2.5L TDi and V8 petrol engines. On 2.5L 200 TDi and 300 TDi 4-Cylinder engines this gasket seals t...

Hex Nut - 3/8" UNF - Full is a full-height plain hexagonal nut with a 3/8 inch UNF thread, used as a load-bearing imperial-thread fastener. It is ...

Inlet Manifold Gasket for the V8 petrol engine, forming the seal between the central inlet manifold casting and the cylinder head intake faces. It...

Exhaust Gasket - V8 for the exhaust downpipe assembly on V8 petrol engines. This gasket seals the flange joint at the exhaust downpipe, maintainin...

Shock absorber bush (eye), anti roll bar bush

Circlip for the drive shaft and hub assembly on Land Rover permanent four-wheel drive axles. This circlip locates in a machined groove on the driv...

Joint Washer - front timing cover gasket for Land Rover 4-cylinder petrol and diesel engines. This gasket seals the mating face between the front ...

Water Pump for the 300 Tdi 2.5L turbo diesel engine cooling circuit. The pump bolts to the engine front cover and circulates coolant through the cy...

Track Rod End Boot - Polyurethane for the steering track rod end ball joint. This polyurethane boot fits over the track rod end housing, sealing t...

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Fuel Connector Block Strainer O-Ring for the Td5 2.5L 5-Cylinder diesel engine. This O-ring seals the strainer within the fuel connector block, pr...

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Major Service Kit for the 2.5L Td5 engine, containing the filtration and service consumables for a full scheduled service. Kit contents: 1 x oil f...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Brake Pad Fitting Kit for front brake assemblies running vented discs. The kit supplies the retaining hardware that secures and correctly positions...

Fir Tree Fastener in light grey, for the roof trim and headlining assembly. Push-fit fastener that secures roof trim panels and headlining ancilla...

Transfer Box Gear Lever Knob fitted to the LT230 transfer box gear lever in vehicles where the LT230 is paired with the LT77 main gearbox. The lev...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Thermostat for the 2.5L 300TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. The thermostat regulates ...

Water Pump Housing Gasket for the 300 TDi cooling circuit, sealing the coolant pump distance piece to the cylinder block. The gasket forms the coo...

Transmission Brake Dust Cover for the central handbrake drum on the transmission output shaft. This cover shields the handbrake drum and brake sho...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...