Land Rover Discovery Parts

Steering knuckle fulcrum bracket assembly used within the front axle swivel and steering knuckle pivot arrangement. The bracket forms the lower p...

Rear Bush Kit for the trailing arm and A-frame rear suspension assembly. This kit provides the rubber bushes for the chassis mounting points of th...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Camshaft Cover Grommet sealing the camshaft cover to the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The grommet forms a stat...

Fuel Tank Breather Hose for the fuel filler and tank ventilation circuit. Connects the fuel tank to the filler neck, venting the tank so that air ...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Towing Socket Plate for the trailer towing electrics. This mounting plate carries the trailer electrical socket at the rear of the vehicle, provid...

Sump Gasket for the 2.0L MPI T-Series 4-cylinder 16-valve petrol engine, sealing the oil sump to the underside of the cylinder block. It forms the...

Flange Bolt - M8 x 130mm, used to secure the coolant pump (water pump) on the 2.5L 300 TDi diesel engine. The integrated flange beneath the head s...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

USB Charging Socket - a dashboard-mounted charging socket that fits a standard factory switch aperture, giving a flush, integrated appearance in pl...

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

A-Frame Ball Joint Bracket forms the pivot connection at the apex of the rear axle A-frame linkage. It mounts to the rear axle housing and locates ...

Clutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...

Coolant Expansion Tank with a clear (translucent) body, part of the engine cooling system. The tank serves as the system's pressurised reservoir a...

Rocker Arm for the rocker shaft valvetrain assembly of the Rover V8 petrol engine. The rocker arm pivots on the rocker shaft and transmits the lif...

Piston Ring Set for the 300TDi diesel engine, supplied in standard size. The set provides the compression and oil control rings for one piston. Fo...

Main Bearing Set for the 2.5L 4-cylinder engine (200 TDi, 300 TDi and the related 2.5 diesel and petrol units), supplied at standard size. The mai...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the big-end bearing shells that sit between the connecting rods and the cranks...

Pinion Bearing - 35 × 68.5mm, a tapered roller bearing installed on the Constant Mesh Pinion shaft within the LT77, R380, and LT95 manual gearboxes...

Piston Ring Set supplies the sealing rings for one piston of the 3.5L V8 petrol engine, in standard (non-oversize) bore size. The rings seal the p...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Front Propshaft transmits drive from the transfer box front output flange to the front axle differential pinion. Forming part of the four-wheel-dr...

Intercooler Hose for the 2.5L 300TDi 4-cylinder turbo diesel engine on EGR-equipped variants. This rubber hose connects the intercooler to the int...

Carpet Drive Fastener is a trim fastener used within the interior floor carpet assembly to secure the carpet to the floor. The fastener is driven ...

Exhaust Bracket supports and locates a section of the exhaust system against the underbody. It carries the weight of the exhaust at its mounting p...

Locking Wheel Nut Key – Code A. Removal key for code-A locking wheel nuts. The key code is stamped on the original key and cannot be derived from t...

Hose Clip for radiator hose connections on 4-cylinder TDi diesel engines. This screw-type hose clip secures the upper and lower radiator hoses at ...

Flange Bolt for the Td5 2.5L five-cylinder turbo diesel engine. The integral flanged head spreads clamping load across the joint face and removes ...

EGR Valve to Pipe Gasket for the diesel exhaust gas recirculation (EGR) system. The gasket seals the flanged joint between the EGR valve and the r...

Dowel is a precision locating pin used to align mating components in the drivetrain, such as the bell housing, gearbox casing and flywheel or drive...

Flange Bolt is an M8 x 35 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Fuel block connector assembly (+hoses) TD5 L318;L316

Rocker Shaft Clamp for the cylinder head valve train on the 300TDi 2.5L turbo diesel engine. Secures the rocker shaft to the cylinder head pedesta...

Bolt - a hexagonal-head bolt with an M6 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the vehicl...

Crankshaft Sensor Spacer for the Land Rover Td5 2.5-litre 5-cylinder turbo diesel engine in manual transmission applications. This spacer fits bet...

Blanking Plug - a push-fit plug used to close an unused aperture in a body panel, door or interior trim component. It seals the opening against wa...

Bolt - M6 x 30mm is a metric threaded fastener with a 6 mm nominal thread diameter and a 30 mm shank length. It secures bolted joints where an M6 ...

Timing Belt Tensioner Washer for 200TDi and 300TDi engines. This slotted packing washer fits to the timing belt tensioner assembly, setting the co...

Front Cover Bolt - M10 flanged hex bolt used to secure the engine front (timing) cover. It also serves as a general-purpose fixing at engine and dr...

Dowel - Bell Housing Alignment in the gearbox/engine interface assembly. This dowel locates the bell housing accurately relative to the engine blo...

Tensioner Pulley for the air conditioning drive belt on the 2.5L 300TDi turbo diesel engine. It runs against the accessory drive belt and maintain...

Banjo Bolt is a hollow union bolt used in the fuel system of the 200 Tdi and 300 Tdi engines. It secures a banjo hose fitting at the injection pum...

O-Ring is a sealing ring used within the ZF 4-speed automatic gearbox and the LT230 transfer box. This O-ring seals fluid passages or housing inte...

Grommet - rubber sealing grommet, 3/4 inch overall diameter with 1/8 inch centre hole. Used to seal and protect wiring cables where they pass thro...

Carburettor Float Assembly regulates the fuel level in the float chamber of an SU carburettor, governing the fuel available to the metering needle ...

Cooling Fan for the engine cooling assembly. Driven from the front of the engine through the viscous fan coupling, the fan draws air through the r...