Land Rover Discovery Parts

Low Note Horn, a 335 Hz electric horn within the audible warning circuit. Produces the low-frequency tone of a dual-tone horn arrangement, pairing...

Track Rod End with a right-hand thread, forming part of the steering linkage. The track rod end is the articulating ball joint that connects the t...

Spire Clip used to retain front wing panels and heater assembly components. This spring-steel clip slides over a screw or stud thread and grips se...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

This taper roller bearing is designed for installation in the lower swivel pin housing, providing controlled rotational support and load distributi...

Copper Sealing Washer for the oil drain plug of the LT77 and R380 manual gearboxes. The washer forms a leak-free seal between the drain plug and t...

Diesel Fuel Filter - Inline for the 2.5L TDi and Td5 2.5L 5-Cylinder diesel fuel system. Fitted at the sedimentor position in the fuel supply line...

Split Pin locks a castellated (slotted) nut in place, passing through the nut slots and a cross-drilled hole in the shaft to stop the nut working l...

Nyloc Nut with a 5/8" UNF thread, used as a self-locking fastener in the suspension linkage. The nylon insert deforms around the bolt thread on as...

Breather Hose for the 300 TDi crankcase ventilation system. The hose carries crankcase breather (blow-by) gases from the engine breather outlet ba...

Fuel Pump Kit for the mechanical diesel lift pump in the low-pressure fuel supply circuit of 2.5L naturally aspirated diesel, 2.5L turbo diesel and...

Door Trim Clip for the interior door casing assembly. Fir-tree fastener that secures the door trim casing to the door frame, locating it in the pa...

Distributor Cap for the ignition distributor on the V8 EFI engine. The cap seats over the distributor and carries the high-tension current from th...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Exhaust Manifold Gasket for the 3.5L V8 petrol engine. This gasket seals the joint between the exhaust manifold and the cylinder head, preventing ...

Nyloc Nut with an M10 thread - the nylon-insert locking nut used on U-bolt fixings. A nylon collar set into the top of the nut grips the bolt thre...

Oil Filter Housing Gasket for the Td5 2.5L five-cylinder turbo diesel engine, sealing the oil filter housing/adaptor to the cylinder block. It sea...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Wheel Nut - secures an alloy road wheel to the hub, forming the threaded clamping interface between the wheel and hub. It uses a wide-stud profile...

Clutch Slave Cylinder for the hydraulic clutch release system on Defender and Discovery 2 models fitted with the R380 manual gearbox. Mounted on t...

Sump Drain Plug Washer - sealing washer for the engine sump drain plug on the Td5 2.5L 5-cylinder turbo diesel engine. This washer seats between t...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Stub Axle Oil Seal - Inner

Clutch Clip - Push Rod to Lever for the hydraulic clutch actuation system. This spring clip secures the clutch slave cylinder push rod to the clut...

Diesel Fuel Filter - Inline for the 2.5L TDi and Td5 2.5L 5-Cylinder diesel fuel system. Fitted at the sedimentor position in the fuel supply line...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Grommet

Thermostat regulates coolant flow within the engine cooling system, with an opening temperature of 82°C. It remains closed while the engine is col...

Rocker Cover Gasket for the Rover V8 petrol engine, sealing the rocker (valve) cover to the cylinder head. The gasket seats between the cover flan...

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...

Brake Union Nut - Metric Thread for the hydraulic brake pipe circuit. This union nut seals and secures brake pipe connections at the unions throug...

EGR Blanking Kit for the Td5 2.5L diesel, used to remove the exhaust gas recirculation (EGR) valve from the inlet manifold and seal off the EGR fee...

Bolt, M10 x 45 securing the front drive member to the hub. The drive member transmits torque from the axle shaft to the road wheel, and these bolts...

Exhaust Bush - Male is the male-profile rubber mounting bush used in the exhaust system vibration isolation assembly. This bush pairs with the cor...

Ignition Lead Set for the 3.5L Rover V8 petrol engine, carrying the high-tension spark from the distributor to the spark plugs. The set comprises ...

Automatic Transmission Oil Screen Kit for the ZF 4-speed automatic transmission, serving the fluid filtration circuit within the transmission sump....

Reverse & Differential Lock Switch is a plunger-operated switch used in the manual gearbox and transfer box electrical circuits. The same swit...

Air cleaner element installed in the engine intake air cleaner housing to filter incoming air before it reaches the induction system. The element...

Wheel Nut securing a road wheel to the hub, clamping the wheel against the hub mounting face. M16 internal thread and steel construction, to the s...

Centrifuge Oil Drain Pipe Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. Seals the oil drain pipe at the engine's centrifugal oil cleaner...

Front Hub Lock Washer for the front hub and driveshaft assembly. This tabbed washer seats between the hub nut and the hub bearing assembly on the ...

Rocker Cover Gasket for the 2.5L 200TDi diesel engine, sealing the joint between the rocker cover and the cylinder head. Installed at the top of t...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

4-Pin Relay is a multi-purpose electromechanical switching relay used throughout the vehicle's electrical system, where a low-current control signa...

Air Bleed Valve for the fuel filter and sedimenter housing, part of the diesel fuel supply system. Mounted in the filter housing, the valve allows...

Thermostat Housing Gasket Seals the thermostat housing to the cylinder head within the cooling system of the 300 TDi 2.5L turbo diesel engine. It ...

Filler Plug sealing the fill and bleed point of the engine cooling system, fitted to the thermostat housing and the radiator. O-ring is included. ...