Land Rover Discovery Parts

Locking Nut for the steering linkage, securing the adjustable joint onto a heavy-duty drag link or steering rod. Once the joint is set to the corre...

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

Bolt & Lockwasher for securing the inlet manifold on the V8 petrol engine. Supplied as a bolt with its matching lockwasher. The imperial 5/16"...

Ball Steel Bearing

Plain Washer - a flat load-spreading washer used at the body-to-chassis mount fixings. Fitted under the bolt head or nut, it distributes clamping ...

Wheel Stud - Front Drive Shaft Hub is a press-fit threaded stud for the front drive shaft hub assembly. It provides the fastening point that secure...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Outer Shim - 1.35mm - Front Halfshaft / CV Joint This 1.35mm shim is used to set the end-float of the front halfshaft within the CV joint assembly...

Cylinder Head Gasket for the 2.5L 200/300 TDi turbo diesel engine, sealing the joint between the cylinder head and the engine block. It seals the ...

Side Indicator is a wing-mounted side repeater lamp in the vehicle's direction-indicator circuit, supplied as a pair. Each unit uses LED elements ...

Cable Tie, a push-fit strap for routing and securing wiring and hoses. The tie strap bundles and secures wiring looms, pipes and hoses, locating i...

Hose Clip for securing flexible hoses to pipes and stubs throughout the Land Rover. Tightening the clip compresses the hose onto the stub to form a...

Wiper Switch Assembly

Steering Damper - 4-Stage Adjustable for Land Rover Defender 90, 110, and 130. This hydraulic steering damper mounts between the axle and chassis ...

Suspension Kit providing 2 inches of lift in a medium load configuration, combining rated coil springs with All Terrain shock absorbers. Designed ...

Shock Absorber for the rear suspension, controlling axle movement and damping spring oscillation between the axle and the chassis mounting points. ...

Shock Absorber for the rear coil spring suspension system. This big-bore unit is designed for heavily laden and expedition applications where sust...

Front Shock Absorber provides damping control on the front axle for suspension raised by approximately 50 mm. Twin-tube big-bore construction with...

Stud

12N 7-Pin Trailer Socket for the towing electrical system, mounted at the rear of the vehicle. The 12N socket carries the standard trailer road-li...

Locking Wheel Nut for replacing one standard wheel nut per wheel as a theft deterrent. The locking wheel nut features a unique external drive prof...

Rear ABS Sensor Kit for the Anti-lock Braking System. A passive wheel speed sensor that generates a voltage signal as the teeth of the rear axle r...

Injector Pipe - No.4 is a rigid high-pressure fuel line in the injection circuit of the 2.5L 300 TDi turbo diesel engine. It carries metered fuel ...

Brake Caliper Piston Kit - replacement pistons for the rear brake caliper. The pistons run in the caliper bores and, under hydraulic pressure, pre...

Camshaft Bearing Set for the Rover 3.5L V8 petrol engine. Supplies the bearing shells that support the camshaft as it runs within the cylinder blo...

CV Joint Spacer for the front axle drive shaft. Fits on the front halfshaft to correctly space the constant-velocity (CV) joint, setting its seati...

Steel Wheel - a 5.5J x 16 inch tubeless welded steel road wheel, finished in black. The rim carries a 35 mm offset (ET35). Its welded tubeless con...

Flywheel Assembly for the 2.5L Td5 five-cylinder turbo diesel engine, mounted between the engine and the manual gearbox. Bolted to the rear of the...

Heater Inlet Hose is a moulded coolant hose in the cabin heater circuit of the 200TDi 2.5L turbo diesel engine. It carries hot coolant from the en...

Manifold Absolute Pressure (MAP) Sensor, part of the engine management system. The MAP sensor measures the absolute pressure inside the intake man...

Fuel Pump is the in-tank electric fuel pump in the fuel delivery system, mounted within the fuel tank. It draws fuel from the tank and delivers it...

Head Gasket for the Land Rover 300TDi 2.5L 4-Cylinder Turbo Diesel engine, fitted at the cylinder head-to-block joint. This is a multi-layer steel...

Drive Flange Nut - replacement centre nut for the heavy-duty thin-type drive flange, black finish. The drive flange sits at the outer end of the f...

Starter Motor Solenoid is the electromagnetic switch mounted on the starter motor body, forming the switching element of the engine starting circui...

Key Wheel Nut

Bolt is a hexagonal-head fastener from the engine and transmission mounting hardware. It secures the engine and gearbox mounting brackets and thei...

Triple Brake Pipe Clip from the brake pipe routing hardware. It retains three rigid brake pipes side by side in one mounting, holding them at a fix...

Shock Absorber Bush Set for the upper damper mounting, polyurethane. The bushes sit in the upper damper mounting, isolating the damper from its mo...

Panhard Rod - front axle lateral location. The panhard rod ties the front axle to the chassis laterally, resisting sideways movement of the axle w...

Rear Axle Breather Pipe vents the rear axle casing. It equalises internal air pressure as the axle heats and cools, allowing the casing to breathe...

Steel hex full nut, M8 x 1.25 thread, catalogued for the clutch and dual-mass flywheel assembly on the Td5 2.5L 5-cylinder turbo diesel engine. Th...

Brake Disc for the front axle, solid (non-vented) type. Part of the braking system, the disc provides the friction surface the brake pads clamp ag...

Nyloc Flanged Nut - M8 flanged nut with a nylon insert, used on front suspension fixings. The nylon collar deforms around the bolt thread as the n...

Inline Fuel Filter for carburettor-fed petrol engines, fitted in the low-pressure fuel supply line ahead of the carburettor. It traps rust, scale ...

Sound Deadening Pad is an acoustic pad fitted to the rocker cover on the 2.5L 300TDi turbo diesel engine. It damps mechanical noise radiating from...

Coolant Pump Drive Belt for the 2.5L 300TDi turbo diesel engine. It transmits drive from the crankshaft pulley to the coolant pump, driving coolant...