Land Rover Discovery Parts

Rear Dislocation Cone is a suspension component for the rear coil springs, fitted at the spring seat to guide a spring that unseats at full droop b...

Gearbox Extension Case Screw for the R380 5-speed manual gearbox. M5 × 30 Torx head screw used to secure the extension case on the R380 gearbox. T...

Drain Plug Washer is the copper sealing washer for the drain plug on the LT77 manual gearbox. It seats between the magnetic drain plug and the gea...

Universal Joint, heavy-duty, for wide-angle propshafts. The wide-angle geometry allows the joint to operate at the increased angles produced by li...

Thrust Washer is a 1.05mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Shock absorber rear Pro-Comp gas 0-25 mm (+1")

Drain Plug - a threaded plug that seals a drain point and is removed to drain fluid during service. It is used in several locations depending on ap...

Piston Ring (+.020" Oversize) for the 2.5L 200 TDi four-cylinder turbo diesel engine, forming part of the piston, connecting rod and bearing assemb...

Valve spring seat fits both inlet- and exhaust valve springs sold EACH

Clutch Cover Bolt secures the clutch cover (pressure plate) to the flywheel within the clutch assembly. Threaded M8 x 13mm, fitted on the 6-speed ...

Locking Nut for the steering linkage, retaining a track rod end onto the drag link or track rod. Once the joint is set to position, the nut is tigh...

Thrust Washer - mainshaft thrust washer for the R380 five-speed manual gearbox. Located at the mainshaft 5th/reverse gears, it controls end-float ...

Locking Nut, a self-locking fixing used across body trim, door casings and bumper fixings. The locking feature resists loosening under vibration.

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...

Differential Bearing Shim - 0.063in

Seat Belt Anchor Plate twin anchor plate for the rear seat belt assembly, of the forward-facing outer static type. The plate forms the male anchor...

Exhaust Bracket locates and supports the exhaust system, securing a section of the exhaust to the underbody to control movement and isolate vibration.

Baulk Ring - synchroniser baulk ring for the R380 five-speed manual gearbox. Serves the mainshaft 3rd/4th and 5th/reverse synchroniser hubs, match...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Polyurethane Suspension Bush Set in the black compound, for the front and rear coil-sprung suspension. This is a full-vehicle set that replaces the...

Rear Coil Spring for the rear suspension, a heavy-duty rating that raises ride height by approximately 40mm over standard. The increased free leng...

Self-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...

Wing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...

Cylinder Head Dowel for the V8 petrol engine. The dowel is a locating pin fitted to the cylinder block deck that positively registers the cylinder ...

Mainshaft Circlip for the LT77 and LT85 five-speed manual gearbox. It seats on the mainshaft to retain a gear or bearing in position, fixing axial ...

Oil Filter Housing Adaptor - part of the oil filter and oil cooler assembly. It mounts on the oil filter housing and provides the connection betwee...

scew hexagonal head M6 x 45mm 4-speed LT95 and 5-speed gearbox bottom cover plate (with Rover V8 engine)

Exhaust Manifold Heat Shield mounts over the exhaust manifold to protect surrounding components from radiant heat. It deflects heat away from adja...

Vacuum Advance Unit for the ignition distributor on the 3.5L V8 petrol engine. This vacuum capsule mounts on the side of the distributor and conne...

Air Ram - the forward-facing intake head of a raised air intake (snorkel) system, in 3" diameter. Mounted at the top of the snorkel body, it draws...

Gearbox Crossmember - SWB is a weld-on steel chassis crossmember that mounts beneath the gearbox and transfer box assembly, providing structural su...

Fusible Link is a sacrificial circuit-protection device used in the vehicle electrical system. Rated at 60A and identified by its yellow body, it ...

Dowel is a hollow locating dowel ring that aligns two mating housings during assembly, holding their faces in register and taking shear load off th...

Throttle Spring - the return spring in the throttle linkage. Acting on the throttle body spindle, it closes the throttle butterfly and returns the ...

Accelerator Return Spring for the throttle linkage on V8 EFI petrol engines. Returns the throttle to the closed position when the accelerator is r...

JATE Ring Recovery Points - heavy-duty steel rings that replace the original chassis lashing eyes to provide rated vehicle recovery points. The JA...

Fuel Injector for the fuel injection system of the 2.5L 200 TDi diesel engine (reconditioned). The injector atomises high-pressure diesel delivere...

Idler Pulley for the air conditioning auxiliary belt drive on 300TDi engines. Positioned within the A/C belt routing circuit, this pulley guides t...

Bolt Hex-head fastener, M10 x 100mm, used as a chassis and crossmember fixing. Commonly fitted to secure the gearbox crossmember, and used across ...

Hex Nut used in the clutch master cylinder and pipe assembly. This standard hex nut secures hydraulic pipe fittings or mounting hardware within th...

Cylinder Head Bolt - a 7/16" UNC long-type bolt for the Rover V8, part of the cylinder head fixings. This is the longest of the head bolts used on...

Exhaust Valve seats in the cylinder head of the 3.5L V8 petrol engine. It controls the exhaust gas leaving the combustion chamber. Head diameter 3...

Intake Air Valve Assembly is the rubber dust valve fitted to the base of the air cleaner housing in the engine air intake system. This one-way fla...

Hose Clip clamps a hose onto its spigot or fitting, maintaining a sealed joint under pressure.

Cranked Rear Radius Arm - links the rear axle to the chassis, controlling fore-and-aft axle location and reacting drive and braking torque. The cr...

Front Half Shaft Pair for the front axle drive, transmitting torque from the front differential out through the axle casing to the wheel hubs. The...

Pair of Heavy Duty Rear Half Shafts for 90/Discovery 1/RRC 1994 On & 110/130 2002 On