Land Rover Discovery Parts

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Engine Mounting Rubber is a bonded rubber-to-metal isolator in the powertrain mounting assembly. It sits between the mounting bracket and the chass...

Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Joint Washer - 4-Wheel ABS installed at the stub axle interface in the hub assembly of vehicles equipped with 4-wheel ABS. This asbestos-free gask...

Drive Belt - 10mm × 1025mm for the auxiliary drive system on the 2.5L 4-Cylinder diesel and 200TDi engines. This poly-V ribbed belt drives the alt...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

Nyloc Nut - M16 flanged self-locking nut used at suspension link fastenings. The integral flange spreads the clamp load across the joint face and ...

Front Axle CV Joint, 24-spline, for the front drive shaft. The constant velocity joint sits at the outer end of the front axle shaft and transmits ...

Nyloc Nut with a 3/4" UNF thread, used as a locknut on heavy suspension joints. A nylon insert set into the crown of the nut deforms over the bolt...

Flange Bolt securing the rear output (propshaft) drive flange to the output shaft of the LT230 transfer box. Manufactured to a high-tensile specif...

Oil Seal for the front axle swivel pin housing. Seals the front driveshaft where it passes into the inner end of the swivel housing, retaining axl...

Shock Absorber Washer for the rear suspension, outer position. This washer fits over the rear shock absorber mounting, seating against the rubber ...

Ignition Coil - high-tension coil in the ignition system. Converts the low-voltage supply into the high-tension voltage required to fire the spark...

Courtesy Lamp Switch is the door-pillar plunger switch in the interior lighting circuit. Mounted in the door aperture, it is released when a door ...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Joint Washer sealing the mounting joint between the cylinder block and the auxiliary unit driven off the engine: the vacuum pump on diesel engines,...

Drop Arm Ball Joint Kit for renewing the ball joint that connects the steering box drop arm to the drag link. The joint transmits steering input f...

Manifold Stud - M8 x 36 mm - for the Td5 2.5L 5-cylinder turbo diesel engine. The stud threads into the cylinder head to locate the manifold flang...

Oil Pressure Switch for the V8 petrol engine, forming part of the engine oil pressure warning circuit within the lubrication system. The switch th...

Drag Link Ball Joint Kit for the steering box drop arm on power-assisted steering boxes. The ball joint forms the articulating connection between ...

Coolant Expansion Tank Cap - pressure cap for the cooling system expansion tank, rated at 15 psi. The cap seals the expansion tank and regulates s...

Crankshaft Position Sensor for the Td5 2.5L 5-cylinder turbo diesel engine management system. The sensor reads the toothed reluctor on the flywheel...

Fuel Filter Element for the carburettor fuel supply circuit on Land Rover V8 petrol engines. Fitted in-line on the fuel feed pipe between the fuel...

Slipper pad

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Swivel Pin Housing Shim - 0.13mm (0.005") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

Front Cover Gasket seals the timing cover to the front face of the cylinder block on the V8 petrol engine. It fits between the front cover and the...

Injector O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel fuel injection system. This O-ring seats in the groove on the injector body at the cylind...

Crankshaft Oil Seal - Front seals the nose of the crankshaft where it passes through the timing cover on the Td5 2.5L 5-cylinder turbo diesel engin...

Transfer Box Flange Bolt - a 3/8" UNF x 1-1/4" hex-head bolt for the LT230 transfer case front output flange. It secures the drive flange to the f...

Bolt - a metric hexagon-head bolt measuring M10 x 110mm. This is a general-purpose threaded fixing used at structural and chassis mounting points,...

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Speedo drive oil seal LT230

Transmission Handbrake Shoe Set is the friction pair for the drum-type parking brake mounted on the rear output of the transfer box. When the hand...

Rotor Arm for the distributor ignition system. The rotor arm mounts on the top of the distributor shaft and turns with it. It picks up the high-te...

Condenser for the distributor ignition system. The condenser (capacitor) is wired across the contact breaker points inside the distributor. As the...

Water Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...

Compression Olive for rigid fuel pipe unions. This 8 mm ferrule seats between the union nut and the fitting body, compressing onto the pipe as the ...

Shock Absorber Turret Bracket is the front suspension turret that caps the coil spring and carries the upper mounting of the front shock absorber. ...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Fuel Connector Assembly - Pressure Regulator forms part of the fuel pressure-regulation circuit, providing the mounting and connection interface fo...

Front Propshaft Flange Bolt Kit - the high-tensile fasteners that secure the front propshaft to its mating flanges at the transfer box and axle end...

Propshaft Bolt Kit - 4 Bolts & 8 Nuts

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Amber Side Repeater Lamp, a body-side lamp that repeats the direction indicator signal. The amber lens flashes in time with the front and rear ind...