Land Rover Discovery Parts

Screw, M6 x 45, used as a threaded fastener at several points in the drivetrain and pedal assemblies. It secures the lower bellhousing cover to th...

Weld-On Beadlock Ring Kit - a set of four steel beadlock rings for converting 16in steel wheels to a mechanically clamped tyre bead. The inner rin...

Transfer Box Differential Lock Clevis in the centre differential lock linkage. Connects the diff-lock actuating linkage that engages and releases ...

Dowel, used with 3-bolt flange. (For Hardy coupling)

Steel Wheel - a 5.5J x 16 pressed-steel rim finished in Limestone gloss. This is a tube-type rim: it is not sealed for tubeless running and must b...

Wheel Chock for securing a stationary vehicle. Placed against a tyre, the wedge-shaped chock prevents the vehicle from rolling when parked on an i...

Locking Wheel Nut Key - Code H, the keyed adaptor that engages the splined pattern of Code H locking wheel nuts. The key is placed over the lockin...

Anti-Roll Bar Bush locates the anti-roll bar at its mounting to the chassis, holding the bar in position while allowing it to rotate as the suspens...

Locking Wheel Nut Key - Code E, the keyed adaptor that engages the splined pattern of Code E locking wheel nuts. The key is placed over the lockin...

Locking Wheel Nut Set - a set of four keyed security nuts, one per wheel, fitted in place of a standard wheel nut to deter theft of the road wheels...

Replace your worn or missing seat adjuster handwheel cap with this Genuine Land Rover component, designed specifically for Discovery 1 models.

Exhaust Valve for the cylinder head valvetrain of the 200TDi and 300TDi 2.5L turbo diesel engines. It seats in the cylinder head exhaust port and ...

Spare Wheel Cover - a padded vinyl cover that fits over an externally mounted spare wheel to protect the wheel and tyre from weather and dirt. Size...

Spare Wheel Cover - a soft cover that fits over an externally mounted spare wheel to shield the tyre and rim from dirt, road grime, moisture and UV...

Rear Wheel Arch Extension - Front Section, Left-Hand for the two-door body, an exterior body trim panel. This extension fits to the forward part o...

Woodruff Key that locates the timing gear and pulley on the crankshaft of the Rover V8 petrol engine. The key sits in the crankshaft keyway to pos...

Mainshaft Bearing for the LT77 five-speed manual gearbox. This tapered roller bearing supports the gearbox mainshaft, locating it within the gearb...

Polyurethane Suspension Bush Kit - Classic Red grade. This kit replaces the original rubber suspension bushes with polyurethane items in the Polyb...

Detent Spring for the LT230 transfer box. It loads the detent that holds the high and low range and differential lock selectors in position, preven...

Woodruff Key locating the camshaft sprocket on the Rover V8 engine. Fits the 3.5L, 3.9L and 4.2L Rover V8. Not used on the 4.0L or 4.6L engines.

lead link pump washer 90/110 used to fit newer style washer pumps to earlier vehicles

Rear Dislocation Cone is a suspension component for the rear coil springs, fitted at the spring seat to guide a spring that unseats at full droop b...

Gearbox Extension Case Screw for the R380 5-speed manual gearbox. M5 × 30 Torx head screw used to secure the extension case on the R380 gearbox. T...

Universal Joint, heavy-duty, for wide-angle propshafts. The wide-angle geometry allows the joint to operate at the increased angles produced by li...

Thrust Washer is a 1.05mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Rear Lamp Guard fits over the rear lamp unit to protect the lens and housing from impact damage. It shields the light cluster from knocks by branc...

Drain Plug - a threaded plug that seals a drain point and is removed to drain fluid during service. It is used in several locations depending on ap...

Swivel Pin Bearing is the upper needle-roller thrust bearing in the front axle swivel housing assembly. It mounts on the upper swivel pin and carr...

Piston Ring (+.020" Oversize) for the 2.5L 200 TDi four-cylinder turbo diesel engine, forming part of the piston, connecting rod and bearing assemb...

Valve spring seat fits both inlet- and exhaust valve springs sold EACH

Thrust Washer - mainshaft thrust washer for the R380 five-speed manual gearbox. Located at the mainshaft 5th/reverse gears, it controls end-float ...

Heated Rear Window Switch mounts in the instrument binnacle and controls the heated rear window (backlight) demist circuit. The push-operated swit...

Locking Nut, a self-locking fixing used across body trim, door casings and bumper fixings. The locking feature resists loosening under vibration.

Retainer for the steering damper mounting, part of the track rod and steering damper assembly. This stem washer locates on the steering damper mou...

Sensor oxygen INTERMOTOR

Differential Bearing Shim - 0.063in

Seat Belt Anchor Plate twin anchor plate for the rear seat belt assembly, of the forward-facing outer static type. The plate forms the male anchor...

Exhaust Bracket locates and supports the exhaust system, securing a section of the exhaust to the underbody to control movement and isolate vibration.

Baulk Ring - synchroniser baulk ring for the R380 five-speed manual gearbox. Serves the mainshaft 3rd/4th and 5th/reverse synchroniser hubs, match...

Headlamp Assembly - Front, Left Hand for left-hand-drive applications, part of the front exterior lighting circuit. The unit combines the reflecto...

Polyurethane Suspension Bush Set in the black compound, for the front and rear coil-sprung suspension. This is a full-vehicle set that replaces the...

Retaining Clip used in the parking brake (handbrake) assembly and the automatic transmission gear-change linkage. The clip secures a pivot pin or ...

Rear Coil Spring for the rear suspension, a heavy-duty rating that raises ride height by approximately 40mm over standard. The increased free leng...

Self-Tapping Screw Set is a set of general-purpose self-tapping fixings used at panel, trim, finisher and bracket mounting points throughout the ve...

Wing Nut for the air cleaner assembly. This threaded wing nut secures the air cleaner cover to its centre stud, clamping the cover down to retain ...

Steering Shaft - the intermediate shaft in the steering column assembly. It links the steering column to the steering box input, transmitting rotat...

Mainshaft Circlip for the LT77 and LT85 five-speed manual gearbox. It seats on the mainshaft to retain a gear or bearing in position, fixing axial ...

Oil Filter Housing Adaptor - part of the oil filter and oil cooler assembly. It mounts on the oil filter housing and provides the connection betwee...