Land Rover Discovery Parts

Exhaust Manifold Gasket for the TDV6 2.7L and 3.0L diesel engine. This gasket seals the joint between the exhaust manifold and the cylinder head. ...

Brake Disc for the rear axle. This disc is the rotor that the rear caliper clamps to slow the wheel. Sized for the 20-inch brake disc and caliper ...

Lower Timing Gear Belt for the engine timing system on the 3.0L V6 Diesel Gen 2 engine. This belt drives the lower timing gear assembly on the fro...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Crossover Pipe Gasket for the exhaust system, sealing the joint between the exhaust crossover pipe and the exhaust manifold. On the 3.0L V6 (Gen2 ...

Clamp - Tube

Front Radius Arm - LH is a suspension linkage in the front suspension assembly. It connects the front subframe to the wheel knuckle and controls th...

Brake Pad Set - Front Brakes

Brake Pad Set

Aluminium Intake Manifold

Injection Pump Leak-Off Tube for the 3.0L V6 diesel engine. It carries leak-off (return) fuel from the high-pressure injection pump back to the fu...

Manifold - Inlet

Fuel Injector Sealing Washer for diesel injector installations. The washer seals the fuel injector against its seat in the cylinder head, containi...

Manifold - Inlet

Aluminium Intake Manifold

Injection Pump Leak-Off Tube for the 3.0L V6 diesel engine. It carries leak-off (return) fuel from the high-pressure injection pump back to the fu...

Leak-Off Tube - Injection Pump

Bolt

Camshaft - exhaust camshaft for the left-hand cylinder bank of the 3.0L TDV6 turbocharged diesel V6. Mounted in the cylinder head, it operates the ...

Exhaust Clamp - 60mm exhaust joint clamp for the front section of the exhaust system, securing the downpipe to the centre silencer section. Clamps...

Valve Stem Seal seals the point where the valve stem passes through the cylinder head valve guide, controlling the oil reaching the stem and preven...

Clip is a fastening used within the body moulding assembly, retaining exterior trim and moulding panels against the bodywork.

EGR Valve for the exhaust gas recirculation system, mounted on the right-hand side and fed from the exhaust manifold. The valve meters the flow of...

Front Radius Arm - RH is a suspension linkage in the front suspension assembly. It connects the front subframe to the wheel knuckle and controls th...

Front Driveshaft, Left-Hand transmits drive from the front differential to the left front wheel hub within the front axle assembly. Constant-veloc...

Front Drive Shaft for the left-hand (LH) side of the front axle drivetrain. The driveshaft transmits drive from the front differential to the fron...

Front Drive Shaft for the left-hand (LH) side of the front axle drivetrain. The driveshaft transmits drive from the front differential to the fron...

Lazer ST4 Evolution LED Spotlight - a compact four-LED auxiliary driving lamp producing a controlled long-range beam for forward illumination. The...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on modern vehicles equipped ...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on selected vehicles utilizi...

Grille Integration Kit - ST4 Evolution is a vehicle-specific kit that mounts a pair of Lazer ST4 Evolution LED spotlights within the front centre g...

Front Suspension Arm Bush - Inner Mount - the rubber-bonded pivot bush at the inner mounting point of the front suspension arm, within the front su...

Gear Shift Module (GSM) Tester is a diagnostic and repair tool for the rotary gear selector module. The plastic fastener inside the GSM is prone to...

Throttle Body and Motor for the engine intake assembly on the 3.0L V6 Diesel Gen 2 engine. This assembly houses the throttle valve and its integra...

Wheel Bearing - Rear, a component of the rear hub assembly. The rear wheel bearing carries the vehicle's rear load and allows the road wheel and h...

Bonnet Latch for the bonnet (hood) closure mechanism. It engages the bonnet striker to hold the bonnet closed and releases it when operated, formin...

Arm - Front Suspension

Arm - Front Suspension

IDLER-DRIVE BELT 80MM 2.0D 2.0L I4 L462/L494/L538/L550/L551/L560/L663

Idler Pulley for the accessory drive belt system of the 2.0L I4 Ingenium (AJ200 / AJ20) petrol and diesel engine. The idler pulley guides the rout...

Drive Belt Tensioner for the accessory drive belt system of the 2.0L I4 Ingenium (AJ200 / AJ20) petrol and diesel engine. This is a double belt te...

Camshaft Inlet - TDV6 - LH

Gasket cylinder head Grade 3, 3 Hole, 1.22 MM Multi layered steel Reinz

Injector Refit Kit - Cylinders No.3 and No.4 supplies the parts renewed when a fuel injector is removed and refitted, within the fuel injectors and...

Cylinder Head Gasket seals the joint between the cylinder head and the engine block on the 3.0L V6 turbo diesel engine, containing combustion press...

Plug cooling system bleed

Front Cover Gasket for the timing gear cover, sealing the front cover to the cylinder block. Fits the 2.7L and 3.0L TDV6 diesel V6 engines. The ga...