Land Rover Discovery Parts

Self-Tapping Screw – No. 8 × 5/8 in is a general-purpose fastener for securing body, trim and panel fixings. Being self-tapping, it forms its own ...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Air flow meter TD5 replacement

Alarm Remote Transmitter, the handset used for remote operation of the vehicle's anti-theft alarm and central locking system. The unit transmits a...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Flange Bolt, M12 - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing area an...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Brake Light Switch, the stop lamp switch mounted at the brake pedal. When the brake pedal is depressed the switch closes the stop lamp circuit to ...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Fastener clip

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Steering Column Shear Bolt securing the steering column mounting clamp to its bracket. The head is designed to shear off once the specified instal...

Window Switch

Brake Caliper Guide Pin Set for the sliding (floating) disc brake caliper assembly. The guide pins locate the caliper to its mounting bracket and a...

Nyloc Nut with an M8 thread - a nylon-insert locking nut used as a self-locking fastener in threaded assemblies. A nylon collar set into the top o...

Turbo Drain Gasket for the Td5 turbocharger oil drain. The gasket seals the joint where the oil return (drain) pipe meets the underside of the tur...

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Oil Filler Seal seals the oil filler cap against the filler neck on the camshaft (rocker) cover. It sits between the cap and the cover opening, ke...

Sump Plug for the engine oil sump (oil pan), part of the engine lubrication system. It threads into the drain hole at the base of the sump to seal...

Fuel Pipe Double Clip for routing the fuel lines in the fuel delivery system. Retains a pair of fuel pipes along their run, holding them against t...

Copper Sealing Washer used to seal a threaded or banjo joint in the fuel and lubrication circuits. The soft copper deforms under tightening to con...

Trim Clip (Scrivet) is a two-piece plastic push-fit fastener used to secure trim panels, facia sections, splash shields and other clipped-in compon...

Exhaust Mount Washer from the exhaust mounting hardware. It seats beneath the fastener at an exhaust mounting point, spreading the clamp load acros...

Bolt for the brake caliper carrier. Secures the caliper carrier bracket to the hub on disc-brake assemblies, retaining the carrier against braking ...

Locking Nut - an M12 self-locking nut used to secure suspension linkage fasteners. The locking feature resists loosening under the vibration and c...

Bolt M8 X 16 HTSETS 8.8 S/COL sold EACH

Fuel Tank Adaptor Ring secures the in-tank fuel pump and sender unit assembly into the aperture on the top of the fuel tank. The ring locks the pu...

Windscreen Washer Pump An electric pump that draws fluid from the washer reservoir and delivers it under pressure to the washer jets. It press-fits...

Master Lighting & Indicator Switch, a column-mounted stalk within the steering column switch assembly. It controls indicator operation and head...

Differential Flange Mud Shield - a protective shield fitted at the differential pinion drive flange. It sits behind the drive flange, where the pr...

Screw - a self-tapping pan-head fastener used in interior trim assembly. It cuts its own thread into the panel or moulded mounting boss to secure ...

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Expansion Tank Cap

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Screw is a fastener used in cooling and heating system assemblies on Land Rover vehicles.

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Bolt is an M8 x 80 mm threaded fastener used to clamp two components together at a bolted joint. It is tightened into a threaded hole or secured w...

Nut - M8 plain low-profile nut, sold individually. A standard metric M8 nut in the low-profile (thin) form. Used across gearbox, suspension, axle,...

Thermostat housing replacement

Sealing Washer is a copper crush washer used to seal banjo and threaded union joints in the fuel system. Fitted at unions such as the injection pu...

LED Side Repeater is an amber side repeater lamp within the exterior signalling circuit, mounted in the front wing aperture. Each lamp provides la...

CV Joint Circlip - the retaining circlip that secures the constant velocity (CV) joint to the front drive shaft. The circlip locates in a groove o...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Plain Washer in M6 oversize form, with a larger outer diameter than a standard M6 washer. It spreads the clamping load of a bolt head or nut over ...