Land Rover Discovery Parts

Sensor Assembly - Lambda

Exhaust Gasket for the flanged joint between the exhaust front pipe and the catalyst section. It seals the bolted flange where the front pipe meet...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Mass Air Flow Sensor - air mass meter fitted in the induction tract as part of the engine management system. The sensor sits in the intake ducting...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Exhaust Gasket sealing a flanged joint in the exhaust system on Land Rover and Range Rover models fitted with the 2.7L TDV6, 3.0D V6, 2.2D, and 4.4...

Timing Chain Tensioner Guide for the 2.0L 16V TIVCT petrol engine (Si4). The tensioner guide is the pivoting guide arm that the timing chain tensi...

Relay is a 4-pin electromechanical switching relay used within the vehicle's electrical system. A low-current control signal energises the 12V coi...

Mass Air Flow Sensor - air mass meter fitted in the induction tract as part of the engine management system. The sensor sits in the intake ducting...

Brake Calliper Fitting Kit for the rear brake callipers. This kit contains the slider pins and rubber dust boots for the rear brake calliper. The ...

Hex Nut, M24 x 1.5mm securing the constant-velocity (CV) joint stub shaft to the wheel hub within the driveline. The nut retains the CV joint and ...

Iridium Spark Plug for the 2.0L 16V turbocharged petrol engine. The iridium centre electrode withstands the high cylinder temperatures and pressure...

Mass Air Flow Sensor - air mass meter fitted in the induction tract as part of the engine management system. The sensor sits in the intake ducting...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Oil Filter - replaceable cartridge filter element for the engine oil cooler and filter assembly, supplied with its sealing ring. The element fits ...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on modern vehicles equipped ...

CANNY is an advanced CAN interface developed by Lazer Lamps that enables the seamless installation of auxiliary lights on selected vehicles utilizi...

Engine Mount Insulator for the engine support and mounting system. This rear lower insulator supports the engine on its mounting and isolates engi...

Oil Pump Chain Tensioner for the 2.0L turbocharged direct-injection petrol engine. Maintains correct tension on the oil pump drive chain, taking u...

Crankshaft Timing Gear for the 2.0L 16V TiVCT turbocharged petrol engine (Si4 240PS and Gen2). It mounts on the nose of the crankshaft and drives t...

Oil Pump Chain is the drive chain for the engine oil pump on the 2.0L 16V turbocharged petrol engine. It transmits drive from the crankshaft to th...

Timing Chain Tensioner Guide for the 2.0L 16V TIVCT petrol engine (Si4). The tensioner guide is the pivoting guide arm that the timing chain tensi...

Timing Chain Guide for the 2.0L 16-valve turbocharged petrol engine, fitted in the timing gear assembly at the front of the engine. The guide loca...

sensor exhaust gas 2.2L CR DI 16V Diesel OEM Autotec

Throttle body with integrated actuator motor for the 2.2L DW12 common-rail diesel engine. Mounted in the intake tract ahead of the inlet manifold,...

Mass Air Flow Sensor - air mass meter fitted in the induction tract as part of the engine management system. The sensor sits in the intake ducting...

Oil Filter filters the engine oil on the 2.0L 16V turbocharged petrol engine. Part of the oil cooler and filter assembly, it removes contaminants ...

Front Door Latch - LH for the front door locking assembly, left-hand side. This latch mechanism mounts inside the front left-hand door and retains...

Door Latch for the rear door, left-hand side, operating within the door lock control assembly. The latch engages the striker on the body aperture t...

Size/Diameter: 433 MHZ door lock frequency

Clutch Repair Kit for the 6-speed manual (M66) transmission on 2.2L diesel applications. The clutch transmits drive from the engine flywheel to th...

Inlet Manifold Gasket Kit - gasket set for the inlet (intake) manifold of the 2.2L TD4 diesel engine. Renews the sealing between the inlet manifol...

Iridium Spark Plug for the 2.0L 16V turbocharged petrol engine. The iridium centre electrode withstands the high cylinder temperatures and pressure...

Steering Wheel Switch mounted in the steering wheel control cluster, providing the voice input (voice recognition) control. For leather steering w...

Pollen Filter for the cabin air intake, part of the HVAC ventilation system. It installs in the intake housing upstream of the blower motor and eva...

Exhaust Manifold Gasket seals the exhaust manifold to the cylinder head on the 2.0L 16V petrol engine. Fitted between the head's exhaust ports and...

Vacuum Pump Seal - the sealing ring for the engine-mounted vacuum pump. The vacuum pump generates the vacuum used by the brake servo; this seal cl...

Valve Cover Gasket seals the cylinder head cover (rocker cover) to the cylinder head on the 2.0L 16V petrol engine. It forms the oil-tight joint a...

2.2L diesel 16V

Clutch Cover Bolt secures the clutch cover (pressure plate) to the flywheel within the clutch assembly. Threaded M8 x 13mm, fitted on the 6-speed ...

Oil Filter filters the engine oil on the 2.0L 16V turbocharged petrol engine. Part of the oil cooler and filter assembly, it removes contaminants ...

Differential Bearing Shim - 0.063in

Pump - Water Hepu

The ultimate diagnostic tool for DIY use offering functionality previously only available in equipment many times more expensive. Standard diagnos...

Camshaft Cover Gasket Set

torx screw and washer, M6x18mm OEM

Locking Wheel Nut Kit for alloy wheels. The locking wheel nuts replace standard wheel nuts to provide theft resistance for the road wheels; each n...