Land Rover Discovery Parts

Crankshaft Pulley Bolt for the Td5 2.5L five-cylinder turbo diesel engine, securing the crankshaft pulley and torsional vibration damper to the nos...

Oil Filter - a replaceable oil filter element housed within the engine oil cooler and filter assembly of the 3.0L V6 turbo diesel (TD6) engine. Th...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Hex Nut is an M8 hexagonal nut, a threaded fastener tightened onto a matching M8 bolt or stud with a standard spanner or socket.

Thermostat regulates coolant flow through the cooling circuit, holding the coolant in the block until operating temperature is reached and then ope...

Split Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...

Fuel Filter for the diesel fuel supply system of the 2.2L DW12 common-rail direct-injection turbo diesel engine. It is fitted in the fuel line betw...

Gasket - Transfer Box Gearchange Housing Plate

Oil Pump O-Ring, a seal within the engine oil pump assembly. The O-ring seals the oil pump strainer (pickup) joint, maintaining the suction seal s...

Overcentre Catch - a spring-loaded toggle latch used to secure hinged covers, lids and access panels. When the lever is thrown past its centre poi...

Brake Pad Set for the front axle disc brake assembly. The pads locate within the front calipers and clamp against the vented front discs, generatin...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

grommet washerpump to reservoir

Bolt with a 3/8" UNF (Unified National Fine) imperial thread and a 4-1/2" shank length. A long-shank hex-head fastener for general assembly and fi...

Clutch Driven Plate (235mm) transmits engine torque from the flywheel to the gearbox input shaft within the clutch assembly. The friction plate sp...

Bolt - 5/16" UNC x 4-3/4" is a hex bolt that secures the water pump and power steering pump on the Rover V8 engine. It has a 5/16" UNC thread and ...

Extended Bump Stops are compression-travel limiters that sit between the axle and the chassis to cap suspension up-travel and cushion the axle agai...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

Front Shock Absorber Turrets: the tubular mounting towers that locate the upper end of the front dampers. Each turret bolts to the chassis and pro...

Thermostat assembly

Idler Pulley guides and supports the timing belt on the 300 TDi 2.5L turbo diesel. Running on a sealed bearing, it routes the belt around the timi...

CLUTCH KIT - COVER + PLATE + BEARING - TD5 - D2/DEF 83-06

Timing Belt - toothed camshaft drive belt for the 200 TDi engine. Synchronises the crankshaft with the camshaft and injection pump, holding valve ...

Spark Plug for the petrol engine ignition system, fitted to the 2.5L four-cylinder and 3.5L/3.9L V8 petrol engines. It screws into the cylinder he...

EGR Valve to Pipe Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. It sits within the exhaust gas recirculation (EGR) system. The gasket se...

Timing Belt for the camshaft drive of the 300 TDi diesel engine, running within the timing belt and tensioner assembly at the front of the engine. ...

Pipe Clip, a routing clip that retains pipework and small-bore lines against the chassis, body or transmission casing. It supports breather, fuel,...

Differential Washer is a plain washer used within the front and rear differential assembly. It seats beneath a threaded fastener to distribute cla...

Bolt - a threaded fastener used within the axle and suspension assembly. It secures front axle case mountings and rear suspension arm attachments,...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Brake Pipe Union is a male threaded fitting used in the brake hydraulic pipework. It belongs to the brake pipe and fitting group. The union nut th...

Differential Thrust Washer for the LT230 transfer box centre differential. It bears against the differential gears within the centre differential,...

O-Ring - Gear Change Selector seals the gear change selector shaft where it enters the transmission housing, preventing lubricant leakage at the sh...

Clutch Slave Cylinder Bleed Screw for the hydraulic clutch release circuit. It threads into the clutch slave cylinder, at the highest point of the ...

Spring Washer is a split spring lock washer fitted under a nut or bolt head to maintain clamping tension and resist loosening caused by vibration. ...

This new Terrafirma winch has a powerful 6hp, 12v motor combined with a 3-stage planetary gearbox that gives over 5 tonnes of pulling power. It has...

Master Lighting & Indicator Switch, a column-mounted stalk within the steering column switch assembly. It controls indicator operation and head...

Lock Nut used to secure interior trim components, including the carpet and sill finishers and the associated bodyside and dust seals. The hex nut ...

Transmitter temperature ORANGE

Temperature switch yellow

Lower Strut Gaiter for the rear self-levelling suspension unit. This flexible rubber boot fits over the lower ball joint of the self-levelling str...

Hex Nut is a metric M5 hexagonal nut used as a general-purpose threaded fastener across multiple vehicle assemblies. It runs onto a matching M5 ma...

Fuel Filter - the primary fuel filter in the low-pressure supply circuit of the 3.0L V6 diesel engine. Positioned between the fuel tank delivery l...

Differential Flange Mud Shield - a protective shield fitted at the differential pinion drive flange. It sits behind the drive flange, where the pr...

Cylinder Head for the Td5 2.5L 5-cylinder turbo diesel engine, later type. The cylinder head seals the top of the engine block, forming the combust...

Snap Ring retaining the rubber dust boot on a track rod end within the steering linkage. A spring-steel ring that seats in the outer groove of the...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...

Exhaust Manifold to Turbo Gasket seals the joint between the exhaust manifold outlet and the turbocharger inlet within the exhaust manifold and tur...