Land Rover Discovery Parts

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Window Control Switch for the driver's door, in the double configuration. The switch is mounted in the driver's door armrest and operates the elec...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Key Fob Battery - CR2032 3V lithium button cell for Land Rover remote central locking handsets. Fits directly into the remote key fob housing. Rep...

Suspension Arm - Front - LH is a front control arm fitted to the left-hand side of the front suspension assembly. It locates the front wheel hub c...

Brake Pad Set - Rear - Less Springs is a replacement rear brake pad set for the rear axle disc brake assembly. The set is supplied without retainin...

Primary Fuel Filter for the diesel fuel supply system of the 2.0L I4 diesel (AJ200 / AJ20D4 / AJ21D4) engine. The primary filter separates water a...

pad foam OEM, eneregy absorbing. (Bij filter LR111341)

Oil Drain Plug for the engine oil pan (sump). Threaded into the base of the oil pan, it seals the oil drain point and is removed to drain the engi...

Wheel Centre Cover fits into the central hub bore of an alloy wheel, concealing the hub and wheel-mounting hardware behind a finished cap that clip...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Valve - Control

Latch hood, bonnet, RH and LH, with sensor

Timing Chain Kit for the Ingenium 2.0L 4-cylinder engine, covering the complete timing chain system. The Ingenium AJ200 engine uses a dual-chain a...

Kinetic Recovery Rope - vehicle recovery accessory for extracting a bogged or stuck vehicle. Unlike a static strap, a kinetic rope stretches under...

EGR Cooler Filter for the low-pressure exhaust gas recirculation circuit of the 2.0L I4 Ingenium diesel engine. The low-pressure EGR system draws ...

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...

Coolant Temperature Sensor in the engine cooling circuit. This sensor monitors coolant temperature and transmits a signal to the engine management...

Parking Sensor is an ultrasonic sensor for the Park Distance Control (parking aid) system. Mounted in the bumper, it emits and receives ultrasonic...

Rear LH height sensor

Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...

Knock Sensor mounts on the cylinder block and detects engine knock through block vibration. It reports combustion knock to the engine management s...

Brake Pad Wear Wire is the rear brake pad wear warning sensor, fitted to the rear brake pads within the rear disc and caliper assembly. The wire c...

Oil Cooler Gasket seals the oil cooler within the oil cooler and filter housing assembly. It maintains the oil-tight joint between the cooler and ...

Exhaust Gas Pressure Sensor mounted in the front pipe / catalyst section of the exhaust system. The sensor measures exhaust gas pressure and repor...

Injector Refit Kit supplying the seals needed to refit a fuel injector on petrol engines. It restores the sealing interface between the injector an...

Accessory Drive Belt - multi-rib belt driving the engine's front-end accessories. Transmits crankshaft rotation to the belt-driven ancillaries wit...

Thermostat Seal for the thermostat housing on AJ200/AJ20 series petrol and diesel engines. It seals the thermostat housing joint within the cooling...

Bolt used in the front brake disc and caliper assembly. This is a securing fastener within the front braking installation.

Fuel Injector Sealing Washer for the fuel injection system. Seals the fuel injector against the cylinder head, maintaining the combustion seal and...

Emission Gasket for the crankcase cover, part of the crankcase ventilation and emission-control system on the 2.0L AJ200/AJ20D4 four-cylinder diese...

Timing Chain Tensioner Arm bears against the timing chain within the timing drive assembly, providing the face through which the tensioner applies ...

O-Ring sealing the variable valve timing (VVT) solenoid cover. Seals the VVT solenoid cover within the engine timing gear, preventing oil leakage ...

Sealing Ring - 34.2 x 3.0mm O-ring that seals a joint in the thermostat housing and EGR cooling circuit. Fitted to the 2.0L four-cylinder AJ200/AJ...

Connecting Rod Bolt secures the connecting rod big-end cap to the connecting rod within the crankshaft, pistons and bearings assembly. The bolt cl...

Guide - Timing Chain

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...

Hex Nut is an M6 flange nut with a 10mm hexagonal drive. It retains wheel arch liner and splashguard panels on their mounting studs. The integral ...

Nut and Washer Assembly is an M6 hexagonal nut supplied together with its washer as a single assembly. The washer spreads the clamping load across...

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Blanking Plug - timing chain cover, supplied with its O-ring. Seals a machined service aperture in the timing chain cover of the Ingenium engine f...

Tie Rod from the steering linkage, running between the steering rack and the steering knuckle. It transmits rack travel to the hub carrier to stee...