Land Rover Discovery Parts

Washer - 20mm

Self-Tapping Screw – No. 8 × 1/2 in is a general-purpose fastener used across body, trim and electrical fixings, such as lamp guards, wheelguards, ...

Valve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...

Air Spring Retainer Clip

Clutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...

Clutch Slave Cylinder, part of the hydraulic clutch release circuit on manual transmission applications. Mounted at the clutch housing, it receive...

Grommet

Timing Belt Kit - 200TDi is a timing system service kit for the 200Tdi 2.5L turbo-diesel engine. The kit renews the components that maintain camsh...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

Accelerator Pedal Lever Pad is the moulded rubber pad that fits over the accelerator pedal lever. It provides the contact face between the driver's...

Head Bolt Kit - a complete set of cylinder head bolts for the Rover V8 engine, securing the cylinder heads to the block and clamping the head gaske...

Selector yoke spherical bush

Rubber Head Plug closing a machined oil-way opening on the 200Tdi 2.5L four-cylinder turbo diesel engine. The rubber plug seals an oil gallery ope...

Flange Screw, M6 x 16mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washer...

Track spacer oil seal

Timing Cover Plate Gasket sealing the timing gear cover plate on the 300Tdi 2.5L four-cylinder turbo diesel engine. The gasket forms the joint bet...

Crankshaft Rear Oil Seal for the engine bottom end, fitted at the rear of the crankshaft where it exits the block towards the flywheel. The seal r...

Drive Belt (V-belt) for the engine accessory drive system, transferring rotation from the crankshaft pulley to a driven accessory. This is a 13 mm...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

Coolant Expansion Tank Cap – the pressure-relief cap that seals the cooling system's expansion (header) tank. Rated to 15 psi, it holds the system...

Lower Ball Joint - Front Hub for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint;...

Flange Head Screw, metric M6 x 20 mm. The integral flange beneath the hex head spreads the clamping load over a wider area and helps resist looseni...

Glow plug TD5

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

Relay, a 70A 4-pin grey mini power relay. It provides high-current make-and-break switching for a heavy electrical load, letting a low-current con...

Plain Washer for M10 fasteners. A flat washer fitted under a bolt head or nut to distribute the clamping load across the joint face, spread bearin...

Clutch Kit is a matched three-piece clutch assembly for the 2.5L 200TDi and 300TDi turbo diesel engines with manual transmission. The kit renews t...

O-Ring for the Td5 fuel pressure regulator. This O-ring seals the fuel pressure regulator within the Td5 fuel system, maintaining a leak-tight joi...

Hex-head bolt, 1/4" UNF thread, 7/8" long. Unified Fine (UNF) thread form with a hexagonal head for use with standard imperial spanners and socket...

Locking Wheel Nut Cap for the wheel mounting assembly. It is a push-on cover that fits over the wheel nut to conceal and protect it, keeping out ro...

Air Spring – Rear for self-levelling rear suspension that uses pneumatic air springs in place of conventional coil springs. Each air spring mounts...

Anti-Roll Bar Bush for the Active Cornering Enhancement (ACE) actuator mounting within the suspension stabiliser assembly. In an ACE-equipped syst...

Water Pump from the engine cooling system of the Td5 2.5L 5-cylinder turbo diesel. It circulates coolant through the cylinder block and cylinder h...

Front Anti-Roll Bar Bolt secures the front anti-roll bar within the front suspension assembly. It fixes the bar to its mounting, holding it in pos...

Shock Absorber Bush - Rear Upper is the mounting bush at the upper end of the rear shock absorber, where the damper attaches to its body mounting. ...

Alternator - Lucas A127 type, 65 A output. Part of the charging system: driven by the auxiliary belt from the crankshaft pulley, it generates the c...

Coolant Temperature Sensor threads into the engine coolant circuit and reports coolant temperature to the instrument and engine management systems....

Drive Shaft Oil Seal - Front, fitted at the front axle swivel pin housing. This radial lip seal runs on the front driveshaft where it passes throu...

Hydraulic Fluid - Rock Oil Power Steering and Active Cornering Fluid, 1 litre. Formulated for power steering systems and Active Cornering Enhanceme...

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...

Clutch Hose forms part of the clutch hydraulic circuit, carrying fluid between the clutch master cylinder and the slave cylinder. The flexible hos...

Castle Nut (castellated nut) used to retain halfshafts, output shafts and differential pinion shafts in Land Rover axle and drivetrain assemblies. ...

Injector Bolt secures the fuel injector clamp within the cylinder head on the 2.7 and 3.0 V6 diesel engines. The M6 x 35 mm bolt retains the clamp...

Gasket for transfer box gearchange lever housing plate LT230 with LT85, LT77, Chrysler 3-speed or ZF 4-speed automatic. Also part of gasket kit RTC...

Output Shaft Seal for the extension housing of the ZF 4-speed automatic gearbox. The seal fits at the rear of the gearbox, where the output shaft ...

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Brake Pipe Clip (double) for ABS-equipped braking systems, used to route and secure rigid brake pipes. The double form holds two brake pipes side ...

Fuel Pipe Clip securing fuel pipe within the fuel delivery system. The clip retains and locates the fuel line along its routing, holding it agains...