Land Rover Discovery Parts

Timing Belt Kit for the camshaft drive of the 2.5L 300 Tdi turbo-diesel engine. The timing belt synchronises crankshaft and camshaft rotation to m...

sensor lambda, Sensor-oxygen multi point injection

ATF - Dexron III is an automatic transmission fluid meeting the Dexron III specification, supplied in a 5 litre container. It is a hydraulic fluid...

Rear Wiper Blade is the wiping element for the rear wash/wipe system, mounted on the tailgate wiper arm. It clears rain and road spray from the re...

Grease Nipple is a long-thread lubrication fitting with a UNF thread form, used to deliver grease into propshaft universal joints and sliding splin...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Cam Cover Sealing Washer Seals a camshaft cover retaining bolt on the 300 TDi 2.5L turbo diesel engine. Fitted beneath the head of the cam (rocker...

Heater Inlet Hose is the coolant feed hose supplying the heater matrix in the cabin heating circuit. It carries hot coolant from the engine to the...

Anti-Rattle Clip secures the linkage rod within the door latch and lock mechanism. It retains the lock linkage rod at its connection point, holdin...

Power Steering Reservoir

Tab Washer for the steering drop arm retaining nut on the Adwest steering box. Fitted beneath the drop arm nut on the steering box output shaft, t...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Sedimentor Sealing Ring for the diesel fuel filter and sedimentor assembly. The sedimentor separates water and sediment from the diesel fuel befor...

Flanged Nyloc Nut, M10, a multi-purpose locking fastener used across the chassis and suspension. The nylon insert resists loosening under vibratio...

Oil Filter for the Td5 2.5L five-cylinder turbo diesel. Part of the engine lubrication system. The filter is a replaceable cartridge element that ...

Swivel Ball Inner Bearing Housing for the front axle swivel assembly. It locates and supports the inner bearing within the swivel ball, maintaining...

Shock Absorber Bush - Polyurethane is a polyurethane mounting bush that fits into the shock absorber mounting eyes, locating the damper at its chas...

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Fuel Tank Breather Hose for the fuel filler and tank ventilation circuit. Connects the fuel tank to the filler neck, venting the tank so that air ...

Rocker Cover Sealing Washer seals a rocker cover retaining bolt on the 200Tdi 2.5L turbo diesel engine. The washer fits under the rocker (valve) c...

O-Ring sealing the front crankshaft (timing) sprocket within the timing case of the 2.5L 300TDi turbo diesel engine. It forms an oil-tight seal ar...

Core Plug (Cup Type) for sealing the core holes left in the engine block casting after the sand cores are removed during manufacture. The cup-shap...

Clutch Master Cylinder - 200TDi, VM & V8

Taper roller bearing for the swivel pin housing assembly within the front axle system. This bearing supports radial and axial loads generated at ...

Upper Gasket Kit for the 300Tdi 2.5L 4-cylinder turbo diesel engine. The kit supplies the gaskets and seals needed to refit the cylinder head afte...

screw M5 x 12

Rear Upper Suspension Arm for the right-hand side, forming part of the rear independent suspension linkage. It connects the rear hub carrier to th...

O-Ring for the power steering hydraulic circuit. The ring seats at a hydraulic union in the steering system, sealing the joint against the pressur...

Polyvee Auxiliary Drive Belt running in the engine front-end auxiliary drive, transmitting rotational drive from the crankshaft pulley to the alter...

Water Pump O-Ring Set: the D-ring (O-ring) set for the coolant pump (Land Rover description 'Set-coolant pump D ring'), renewed whenever the pump i...

Ball Joint for the anti-roll bar drop link. It forms the pivoting connection at the end of the anti-roll bar, linking the bar to the suspension so ...

Spring Retainer secures the upper outer mounting of the rear coil spring and damper within the rear suspension assembly. It clamps the top of the ...

Castle Nut - M12 castellated nut used on the steering and suspension ball-joint fixings. Its slotted crown takes a split pin through the drilled h...

Head Gasket for the Td5 2.5L 5-cylinder turbo diesel engine, sealing the joint between the cylinder head and the cylinder block. It seals the comb...

Interior Door Handle for the right-hand side. Part of the door latch and release mechanism. Mounted on the inner door, the handle operates the lat...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This version c...

Gearbox Selector Ball is a hardened steel detent ball used in the manual transmission gear-selection mechanism. Spring-loaded against the selector...

Track Rod End with right-hand thread, fitting at the outer end of the track rod within the steering linkage on the Defender, Discovery 1, and Range...

Front Crankshaft Oil Seal installed in the front cover assembly, part of the engine's crankshaft sealing arrangement. Seals the running clearance ...

Water Pump for the Rover V8 EFI petrol engine, supplied with gasket. The water pump sits in the engine cooling circuit and is belt-driven from the...

Brake Caliper for the rear braking assembly, mounted on the left-hand side. The caliper houses the piston and hydraulic fluid inlet, converting pr...

O-Ring for the power steering hydraulic circuit, sealing a connection within the pressurised steering fluid system. This is the brown, thick-secti...

Auxiliary Drive Belt for the front-end accessory drive system, transmitting drive from the crankshaft pulley to the alternator and other engine anc...

Shock Absorber Mounting Washer (inner), used at pin-type shock absorber mountings within the suspension damper installation. It seats on the mount...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Hub Bearing - Taper Roller - Front & Rear is a taper roller wheel bearing for the front or rear hub assembly. Each bearing is made up of a tap...