Land Rover Discovery Parts

Air flow meter TD5 replacement

Fuel block connector assembly (with hose) TD5

Steering Drop Arm Puller - a specialist tool for drawing the drop arm off the splined output shaft of the steering box. The drop arm is a tight ta...

Front Axle Drive Shaft transmits drive from the front differential to the right-hand wheel hub, forming part of the front axle drive shaft and hub ...

A-Frame Ball Joint Fitting Kit: fitting hardware for mounting the rear A-frame fulcrum bracket and ball joint assembly.

Universal Joint for the propeller shaft assembly, transmitting rotational torque between adjoining shaft sections while permitting the angular move...

Stub Axle Bolt is a hex-head retaining screw that secures the front stub axle to the swivel pin housing. The stub axle carries the wheel hub and b...

Bolt Mounting bolt for the rear suspension arm. Part of the rear multi-link suspension assembly, it secures a rear upper or lower suspension arm a...

Throttle body heater assembly OEM

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Blanking Plug closes off an unused 8mm (5/16 inch) aperture in a body panel or chassis section. It belongs to the body grommets and panel-sealing g...

Oil Pressure Switch monitors pressure in the engine lubrication circuit and signals the instrument gauge and low-pressure warning lamp. Mounts to ...

Fir Tree Fastener push-in fixing in light grey, used to retain headlining, roof trim and similar interior and exterior trim panels. The tapered fi...

Fuel Return Check Valve is a non-return valve fitted in the fuel return circuit of the Td5 fuel system. It permits fuel flow in one direction only...

Split Pin used on a front-axle assembly to lock a castellated nut. The pin passes through the drilled fastener and the slots of the nut, and its le...

Carpet Drive Clip is an interior trim fastener used to retain the floor carpets against the body. The drive-clip design presses into a mounting ho...

Starter Motor for the 2.5L 4-cylinder diesel engine, part of the engine electrical starting circuit. When the ignition is operated the solenoid th...

Brake Light Switch, the stop lamp switch mounted at the brake pedal. When the brake pedal is depressed the switch closes the stop lamp circuit to ...

Injector Clamp Bolt for the Td5 2.5L 5-cylinder turbo diesel engine. It secures the injector clamp to the cylinder head, holding the fuel injector ...

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Brake Vacuum Pump for the 300 TDi 2.5L turbo-diesel engine, mounted on the engine as part of the brake vacuum circuit. Driven mechanically by the ...

Window Regulator Motor - RH is the electric drive motor for the right-hand window regulator assembly. It mounts directly to the window regulator m...

Wheel Centre Cap with a pewter finish, fitting the centre bore of the alloy road wheel. It conceals the hub and the wheel fixings at the centre of ...

Speedo cable oil seal retainer plate

Clutch Release Bush for V8 petrol applications, located within the clutch assembly at the rear of the crankshaft. The bush seats in the spigot rec...

Thermostat Housing Gasket for the 200TDi 2.5L turbo-diesel engine, sealing the thermostat housing to the cylinder head within the engine cooling ci...

Upper Ball Joint for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint; this upper ...

Flywheel Bolt securing the flywheel to the rear flange of the crankshaft. Used on four-cylinder petrol and diesel engines, including the 200TDi an...

O-Ring for the power steering hydraulic circuit, sealing a union on the 6mm power steering pipe. The O-ring seats at the connection between the po...

Radiator Top Hose is the upper coolant hose in the engine cooling circuit. It carries hot coolant from the engine thermostat housing to the top of ...

Heater Outlet Hose is the coolant return hose from the heater matrix in the cabin heating circuit. It carries coolant from the outlet side of the ...

Wheel Centre Cap in a Silver Sparkle finish with the embossed Land Rover logo, fitting the centre bore of the alloy road wheel. It conceals the hub...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Flame Trap fits into the crankcase ventilation circuit of the V8 twin-carburettor petrol engine, between the crankcase breather and the carburettor...

Grommet

Expansion Tank Hose connects the coolant expansion (header) tank into the cooling circuit. It carries coolant between the expansion tank and the r...

Inlet Manifold Gasket for the Rover V8 petrol engine, sealing the inlet manifold where it seats in the valley between the two cylinder banks. This...

Alternator, 120A, for the 2.5L Td5 diesel - the charging-system unit that supplies the vehicle's electrical power and recharges the battery. Belt-...

Drive Belt Idler Pulley for the auxiliary (accessory) belt drive of the Td5 2.5L 5-cylinder turbo diesel engine. The pulley mounts above the water...

Brake Caliper Repair Kit supplying replacement piston seals for overhauling the brake caliper. New piston seals restore the caliper's ability to r...

Screw – a No. 6 × 1/2 in self-tapping screw used to secure interior trim and panel fixings, such as the instrument binnacle, fascia mouldings and a...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Bumper Lamp Assembly, left-hand side, part of the rear bumper lighting cluster. A combined lamp unit with a red lens section serving the stop and ...

Lamp assembly indicator front RH

Fuel Pump & Sender - in-tank low-pressure fuel pump and fuel level sender assembly for the Td5 2.5L 5-cylinder turbo diesel. The unit mounts v...

Sealing Washer seals the engine oil sump drain plug, fitting between the drain plug head and the sump drain boss. When the drain plug is tightened...

Rear Brake Caliper for the left-hand side of the rear axle, part of the hydraulic braking circuit. The caliper carries the hydraulic pistons that ...

Ball Bearing for the transfer box, supporting the output shaft and its output flange. Fitted in the LT230 and NV225 transfer boxes, the bearing lo...