Land Rover Discovery Parts

Oil Gallery Plug for the cylinder block oil gallery on Land Rover 4-cylinder engines. The oil gallery is the network of internal drillings in the ...

Fuel Filter for the diesel fuel supply system of the 2.2L DW12 common-rail direct-injection turbo diesel engine. It is fitted in the fuel line betw...

Air Filter - the air cleaner element for the engine air intake system. The element sits within the air cleaner housing and filters incoming air be...

Plain Washer A flat washer sized for 1/4" fasteners, used as a general-purpose fixing throughout the body, chassis and mechanical assemblies. It s...

Shock Absorber Washer - Rear - a retaining washer used at the rear suspension shock absorber mounting. It seats against the lower shock absorber b...

Hex Nut is an M8 hexagonal nut, a threaded fastener tightened onto a matching M8 bolt or stud with a standard spanner or socket.

Thermostat regulates coolant flow through the cooling circuit, holding the coolant in the block until operating temperature is reached and then ope...

Split Pin - a 1.5mm x 12mm cotter pin used to lock a slotted (castle) nut or to retain a clevis pin. Passed through a drilled cross-hole in the sh...

Saddle Clip for the power steering hydraulic circuit. This saddle-shaped clip clamps a power steering pipe or hose to its mounting point, retaining...

Oil Pump O-Ring, a seal within the engine oil pump assembly. The O-ring seals the oil pump strainer (pickup) joint, maintaining the suction seal s...

Set Screw - a fully threaded hexagonal-head setscrew with a 3/8" UNC (Unified Coarse) imperial thread and a 7/8" length. Used as a Rover V8 engine-...

Heater Hose for the Td5 2.5L 5-cylinder turbo diesel coolant heating circuit, connecting the heater matrix outlet to the fuel cooler. Supplied wit...

Power Steering Pipe for the power-assisted steering hydraulic circuit, carrying pressurised fluid between the steering pump and the steering box. ...

Bracket tie bar for steering box

Overcentre Catch - a spring-loaded toggle latch used to secure hinged covers, lids and access panels. When the lever is thrown past its centre poi...

Brake Pad Set for the front axle disc brake assembly. The pads locate within the front calipers and clamp against the vented front discs, generatin...

Hex Nut with a 5/16" UNF (Unified National Fine) thread. This six-sided fastener threads onto a matching 5/16" UNF bolt or stud and is tightened w...

Radius Arm Bolt, 1/2" UNF, 5-3/4" long, securing the radius arm to its chassis mounting bracket. The radius arms locate the front axle fore and af...

Self-Tapping Screw - a No. 8 x 3/8" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as it ...

grommet washerpump to reservoir

Turbo Oil Drain Pipe for the 300 TDi engine, returning lubricating oil from the turbocharger to the sump. Connects the turbocharger bearing housin...

Spring Washer, 5/16" - a single-coil split washer fitted under a nut or bolt head to maintain clamp tension. The split coil acts as a spring, exer...

Bolt - a hexagonal-head bolt with a 5/16" UNC (Unified Coarse) imperial thread and a 3/4" length. Used as an engine-assembly fixing, including cams...

Air Intake Hose forms part of the engine air intake ducting. It carries filtered air from the air cleaner housing to the throttle body and inlet ma...

Bolt 1/4" UNC x 1-1/4" is a coolant pump fixing bolt used on the 3.5L V8 petrol engine. It secures the coolant (water) pump to the engine within t...

Clutch Driven Plate (235mm) transmits engine torque from the flywheel to the gearbox input shaft within the clutch assembly. The friction plate sp...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

double washer, restrictor

Bolt - M8 x 100mm hex head bolt used in the transmission mounting assembly. Secures transmission mounting components on Series III vehicles equipp...

Timing Chain Tensioner for the Td5 2.5L 5-cylinder turbo diesel, part of the timing chain drive assembly at the front of the engine. The tensioner...

Brake & Clutch Pedal Bush for the pedal box assembly. It forms the pivot bearing where the pedals mount on their shaft, locating the brake and ...

Bolt - 5/16" UNC x 4-3/4" is a hex bolt that secures the water pump and power steering pump on the Rover V8 engine. It has a 5/16" UNC thread and ...

Extended Bump Stops are compression-travel limiters that sit between the axle and the chassis to cap suspension up-travel and cushion the axle agai...

Steering Box Assembly - LHD is the power-assisted recirculating-ball steering box, in the left-hand-drive configuration. It is the central unit of...

Coolant Hose connects the coolant rail to the coolant pump, carrying coolant between the rail and the pump inlet within the cooling circuit. Fitte...

Hub Flange O-Ring for the rear axle drive flange. The O-ring seals the joint between the rear drive shaft flange and the hub, preventing oil leaka...

Throttle Body Gasket seals the throttle body to the plenum chamber on the 4.0L and 4.6L V8 EFI petrol engine. Fitted between the throttle body and...

Headlamp Wash T-Piece - three-way T-connector in the headlamp washer fluid line. Splits the feed hose from the washer pump so a single supply serv...

Exhaust Downpipe - De-Cat for the front section of the exhaust system, fitted downstream of the turbocharger outlet on TD5 diesel applications. Th...

Breather Hose for the crankcase ventilation system on the 2.5L diesel and 200TDi turbo diesel engine. This flexible hose carries crankcase blow-by...

Mainshaft Bearing supports the mainshaft within the LT230 transfer box, carrying the shaft's rotational loads and keeping it running true as drive ...

Coolant Hose - Radiator to Oil Cooler is a moulded coolant hose within the engine cooling circuit. It carries coolant between the radiator and the...

PAS pump assy Disco 2 TD5

Oil Cooler - the replacement cooler element for the Td5 2.5L 5-cylinder turbo diesel engine oil cooling circuit. This is the finned heat-exchanger...

Front Shock Absorber Turrets: the tubular mounting towers that locate the upper end of the front dampers. Each turret bolts to the chassis and pro...

Kit - Tie Rod Repair M20/M12

Thermostat assembly

Brake Disc Mud Shield - Front, LH, mounted behind the left-hand front brake disc. The shield sits between the stub axle / hub and the brake disc, ...