Land Rover Discovery Parts

Double Cardan Joint Kit for the Discovery 2 front propshaft. The Discovery 2 front propshaft uses a double cardan joint assembly incorporating thr...

Brake Caliper Piston Kit - replacement pistons for the rear brake caliper. The pistons run in the caliper bores and, under hydraulic pressure, pre...

Cam Cover Gasket for the 2.5L Td5 5-Cylinder Turbo Diesel engine. This gasket seals the camshaft cover to the top of the cylinder head, preventing...

Rear Coil Spring Spacers, +2" - a pair of suspension spacers for the rear coil springs that raise ride height by approximately 2 inches (50 mm). E...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Crankcase Breather Hose forms part of the closed crankcase ventilation circuit, connecting the rocker cover breather outlet to the intake manifold ...

Gear Linkage Repair Kit renews the worn components of the automatic transmission gear selector linkage. It restores accurate movement between the ...

Steering knuckle fulcrum bracket assembly used within the front axle swivel and steering knuckle pivot arrangement. The bracket forms the lower p...

The cable forms the mechanical link between the handbrake operating lever and the handbrake mechanism within the handbrake assembly, transmitting l...

Main Bearing Cap Bolt - a 1/2" UNC bolt that fastens a main bearing cap to the cylinder block on the Rover V8 engine. It clamps the main bearing c...

Camshaft Cover Grommet sealing the camshaft cover to the cylinder head on the Td5 2.5L five-cylinder turbo diesel engine. The grommet forms a stat...

Thermostat regulates coolant flow within the engine cooling circuit. It stays closed while the engine is cold to speed warm-up, then opens at its r...

Fuel Tank Breather Hose for the fuel filler and tank ventilation circuit. Connects the fuel tank to the filler neck, venting the tank so that air ...

Coolant Hose connecting the radiator to the fuel cooler within the engine cooling circuit. It routes engine coolant to the coolant-cooled fuel coo...

Silicone Turbo & Intercooler Hose Kit - a three-piece set of silicone charge-air hoses for the 300Tdi turbo and intercooler circuit, replacing ...

Towing Socket Plate for the trailer towing electrics. This mounting plate carries the trailer electrical socket at the rear of the vehicle, provid...

Head Gasket Set - V8

Sump Gasket for the 2.0L MPI T-Series 4-cylinder 16-valve petrol engine, sealing the oil sump to the underside of the cylinder block. It forms the...

Toebox Trim Fastener - the fixing that secures the footrest and toebox trim panel in the footwell. It retains the lower trim at the A-post and toe...

Flange Bolt - M8 x 130mm, used to secure the coolant pump (water pump) on the 2.5L 300 TDi diesel engine. The integrated flange beneath the head s...

Cable Tie for securing wiring harnesses and cable runs throughout the vehicle.

Crankshaft Pulley Bolt & Washer for the 2.2L 16-valve turbo diesel (DW12), securing the crankshaft pulley to the nose of the crankshaft. The b...

USB Charging Socket - a dashboard-mounted charging socket that fits a standard factory switch aperture, giving a flush, integrated appearance in pl...

Rear Lamp Bulb Holder Double-pole bulb holder that seats in the rear lamp housing, retaining the bulb and carrying the electrical contacts between ...

Bolt - a hexagonal-head bolt with an M10 metric thread and a 30 mm length. A common general-purpose fastener used at fixing points across the suspe...

Split Pin: a cotter pin that locks a slotted (castle) nut or retains a clevis pin. After fitting, its legs are bent back to stop the fastening work...

Rear Propshaft Coupling Kit - a flexible rubber coupling that connects the rear propeller shaft to the drive flange, transmitting drive while absor...

A-Frame Ball Joint Bracket forms the pivot connection at the apex of the rear axle A-frame linkage. It mounts to the rear axle housing and locates ...

Air-to-Coil Conversion Kit - +2" lift, medium load, with Pro Sport long-travel shock absorbers. Replaces the factory rear air suspension with a co...

Compressor Amk Version

Clutch Kit is a matched three-piece clutch assembly for the 3.5L V8 petrol engine with manual transmission. The kit renews the complete clutch as ...

Radius Arm Bush mounts the front radius arm to the axle within the suspension linkage, at the axle end of the arm. The bush provides a flexible pi...

Body Rivet - a mechanical fastener used within the body and panel assembly to join thin sheet metal, trim and stowage fittings. Nominal size 3/16"...

Coolant Expansion Tank with a clear (translucent) body, part of the engine cooling system. The tank serves as the system's pressurised reservoir a...

Wash Wipe Switch for the steering column switchgear. This column-mounted stalk operates the windscreen wipers and the windscreen washer. It mounts...

Piston Ring Set for the 300TDi diesel engine, supplied in standard size. The set provides the compression and oil control rings for one piston. Fo...

Main Bearing Set for the 2.5L 4-cylinder engine (200 TDi, 300 TDi and the related 2.5 diesel and petrol units), supplied at standard size. The mai...

Steering Column Lock - the steering column lock and ignition switch assembly. Mounted on the steering column, it mechanically locks the column whe...

Connecting Rod Bearing Set for the Rover V8 petrol engine. These are the big-end bearing shells that sit between the connecting rods and the cranks...

Flexible Brake Hose for the rear right-hand side, part of the hydraulic braking circuit. The hose forms the flexible link between the rigid brake ...

Flexible Brake Hose for the rear left-hand side, part of the hydraulic braking circuit. The hose forms the flexible link between the rigid brake p...

Special Nut - secures the rear knuckle to the lower and upper suspension arms. It retains the rear suspension arm bolts at the knuckle, holding th...

Pinion Bearing - 35 × 68.5mm, a tapered roller bearing installed on the Constant Mesh Pinion shaft within the LT77, R380, and LT95 manual gearboxes...

Piston Ring Set supplies the sealing rings for one piston of the 3.5L V8 petrol engine, in standard (non-oversize) bore size. The rings seal the p...

Axle Buffer - the progressive rubber bump stop that limits suspension travel at full compression. Mounted between the axle and chassis, it absorbs...

Rear Upper Knuckle Bush - a rubber-to-metal bush that forms the upper pivot mounting between the rear knuckle and the radius arm in the independent...

Radius Arm Bush for the front radius arm within the coil-sprung suspension assembly. The bush carries the radius arm at its chassis mounting. The ...