Land Rover Discovery Parts

Alternator of the Lucas A133 type, rated at 85A, for V8 EFI petrol engines. Driven by the auxiliary belt from the crankshaft as part of the engine...

Differential Lock Link Assembly for the LT230 transfer box, fitted to vehicles with the LT77 or LT85 5-speed manual gearbox (28D prefix). This lin...

Window Regulator for the front door, right-hand side, manual winder type (not electric). This is the mechanism that raises and lowers the front do...

Fuel Pipe - Cylinder No.4 for the 200TDi 2.5L four-cylinder turbodiesel, part of the high-pressure fuel injection circuit. This steel injection pi...

Steering Box is the steering gear at the heart of the power-assisted steering circuit. It converts steering-wheel rotation into lateral movement o...

Clutch Slave Cylinder Repair Kit for the hydraulic clutch release circuit on V8 petrol applications. The clutch slave cylinder is actuated by hydr...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Intercooler Hose - the charge-air hose connecting the turbocharger to the intercooler on the Td5 2.5L 5-cylinder turbo diesel. It carries pressuri...

Expansion Tank Cap

Coolant temperature transducer for the 3.9L V8 EFI petrol engine, part of the engine management sensing circuit. Threads into the coolant passage ...

Rear Brake Pipe Clip retains and locates the rigid brake pipes along the rear of the chassis. It holds the brake lines securely against the chassi...

Finisher Clip - a retaining clip for exterior body finishers and mouldings. The clip secures a trim finisher or moulding to the body panel, engagi...

Tube - Water Outlet

Crankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...

Door Hinge - Lower for the front door, mounted to the A-pillar to support and align the lower section of the door. Works in conjunction with the up...

Fuel Connector Block Gasket for the Td5 2.5L five-cylinder diesel engine, sealing the fuel connector block to the engine within the fuel pressure r...

Spring Nut is an M10 "U"-type spring-steel clip nut that provides a captive threaded fixing point on panels and brackets. The U-shaped clip slides...

Crankshaft Oil Seal - Front - 300TDi

Oil Filter is the replaceable element in the engine lubrication circuit, capturing wear particles and combustion contaminants from the oil before i...

Centrifuge Oil Drain Pipe Gasket for the Td5 2.5L 5-cylinder turbo diesel engine. Seals the oil drain pipe at the engine's centrifugal oil cleaner...

Front Spring Spacers fit between the front axle and the base of the front coil spring to raise the spring mounting point. The spacers are 50mm (2 ...

Valve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...

Core Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...

Rear Crankshaft Oil Seal seated in the crankshaft rear oil seal housing at the back of the cylinder block, sealing the point where the crankshaft e...

Plenum Hose is a moulded hose serving the plenum chamber of the V8 EFI petrol induction system. It forms part of the plenum chamber assembly on th...

Single-Pole Bulb Holder fitted within the rear lamp assembly, providing the electrical interface and physical retention for the stop or tail lamp b...

Windscreen Finisher - the exterior trim moulding that finishes the upper edge of the front windscreen. Covers the top windscreen seal and the join...

ABS Sensor - Front for the wheel speed sensing circuit on the front axle. This is the short-type sensor, terminating directly in a connector. The ...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Circlip - Output Shaft Flange used within the transfer box output flange assembly to retain the output shaft bearing and associated components in p...

Rear Bush Kit for the trailing arm and A-frame rear suspension assembly. This kit provides the rubber bushes for the chassis mounting points of th...

Drop Arm - Steering Box Output is installed on the steering box sector shaft within the power-assisted steering assembly. This component converts ...

Interior Trim Fixing Clip used within body and interior trim assemblies. This clip secures trim panels, insulation sections, ducting, and fascia c...

Main Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...

Fuse rated at 7.5A for the vehicle electrical system. Fitted in the fusebox to protect a circuit rated at 7.5 amps, the fuse breaks the connection...

Repair Washer - M10 for use in suspension, axle and body fastening applications. A large-diameter flat washer that distributes the clamping load o...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Rear Screen Washer Jet for the tailgate glass wash system. The jet mounts to the rear tailgate and directs washer fluid onto the rear screen. It i...

Fuel Tank Cradle - the support cradle that carries the fuel tank beneath the vehicle, bolting to the chassis to hold and locate the tank. Heavy-du...

Washer - a general-purpose fixing washer used across multiple body, brake and chassis assemblies. It spreads the clamping load of a bolt or nut ov...

Throttle Potentiometer Kit adapts the Rover V8 plenum chamber to accept a Colvern throttle position sensor in place of the original two-bolt potent...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Alternator Mounting Screw for the Rover V8 petrol engine alternator assembly. This screw secures the alternator to its mounting bracket on the eng...

Gearbox Breather for the gearbox and transfer case assembly. This breather is located on the gearbox or transfer case casing and vents internal pr...

Door Glass Channel for the side door glass assembly. The channel locates within the door frame and guides the window glass along its travel as it i...

Torque Converter Housing Cover Gasket for the automatic transmission bell housing. It seals the lower access cover on the torque converter housing...

Bolt - M8 x 40mm standard metric hex-head fastener for use across engine, gearbox, body, and chassis assembly applications.