Land Rover Discovery Parts

Spring Retaining Plate for the front coil spring suspension. The plate seats the upper end of the front coil spring against the chassis spring seat...

Drive Belt is the serpentine (poly-vee) accessory belt for the 4.0L V8 EFI petrol engine fitted with air conditioning. Driven from the crankshaft ...

Brake Light Switch operates the stop lamps within the braking system's electrical circuit. Mounted at the brake pedal, the switch closes when the ...

Idler Pulley - timing belt idler for the 200 TDi and 300 TDi engine. Provides a bearing surface on the timing belt path, guiding the toothed belt ...

Brake Hose - Front - D1

Crankshaft Pulley Bolt for the 2.5L 300TDi diesel engine. This bolt secures the crankshaft pulley and torsional vibration damper to the nose of the...

Trim Clip is an interior trim fixing that retains the A-pillar trim panel against the body structure. Depending on application it also serves as t...

Vacuum Pump O-Ring that seals the diesel vacuum pump at its mounting joint. The vacuum pump supplies the depression used by the brake servo on die...

Shock Absorber Washer Retaining washer for the rear shock absorber lower mounting. Part of the rear suspension assembly, it locates over the lower...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Special Bolt for the front suspension radius arm. This M16 bolt secures the radius arm at its mounting, locating the arm against the chassis and a...

Upper Front Swivel Pin for the front axle swivel housing assembly. The upper swivel pin bolts to the top of the swivel housing and forms the upper...

EGR Valve Gasket

Intercooler Hose for the 200 TDi turbocharged induction system. Part of the charge-air ducting that links the intercooler into the boost circuit, ...

PTO Cover Gasket - LT230 seals the power take-off (PTO) aperture cover on the LT230 transfer box. It forms the joint between the PTO cover plate a...

Oil Relief Valve Sealing Washer seals the oil pressure relief valve within the engine oil pump assembly. It is fitted at the relief valve in the l...

Flat Washer with a 3/8" bore, fitted under a bolt head or nut to spread the clamping load over a wider area and protect the mating surface.

Automatic Transmission Oil Screen for the ZF 4-speed automatic transmission, fitted within the transmission oil sump. The screen filters the autom...

Bump Stop - rear suspension bump stop that limits the upward travel of the axle at full compression. The moulded rubber block cushions the contact ...

Plenum Chamber Gasket for the V8 EFI petrol engine, part of the air intake and induction assembly. The gasket seals the joint at the plenum chambe...

Heater Hose - inlet pipe from the cylinder head to the heater matrix, Td5 2.5L 5-Cylinder Turbo Diesel. Carries hot engine coolant from the cylind...

Release Bearing Guide - the guide sleeve in the clutch release mechanism, mounted on the front cover of the manual gearbox. It encircles the gearb...

Mudshield

Oil Seal Collar for the R380 manual gearbox. The collar fits over the output shaft and provides the hardened running surface against which the gea...

Valve Stem Seal fits over the valve guide at the top of the cylinder head on the 2.5L 200 TDi and 300 TDi diesel engines. It wipes and meters lubr...

Alternator, 120A, for the 2.5L Td5 diesel - the charging-system unit that supplies the vehicle's electrical power and recharges the battery. Belt-...

Poly-Vee Drive Belt for the Rover V8 petrol engine, in the specification fitted to vehicles equipped with ACE (Active Cornering Enhancement) and ai...

Boost Pipe Assembly for the 2.5L 300 TDi turbo diesel, part of the turbocharger boost control circuit. It connects the inlet manifold to the injec...

Rear Bumper Trim Retainer Clip for the Discovery 2 (L318). This plastic retainer clip secures the rear bumper finisher trim at the end-cap section...

Door Handle Cover that caps the exterior door handle at the door lock control, finishing the handle assembly. Supplied in black, this is the blank...

Hex-Head Bolt with a 7/16" UNF (Unified National Fine) imperial thread and a 2" shank length. A fastener used in the manual steering box mounting ...

Bolt - M12 x 60mm is a metric hexagon head bolt used across a wide range of assembly applications on Land Rover vehicles. Thread specification M12...

Locking Nut for the steering linkage, securing the adjustable joint onto a heavy-duty drag link or steering rod. Once the joint is set to the corre...

Anti-Roll Bar is the rear stabiliser bar within the suspension system, mounted transversely across the rear axle. Connected to the suspension thro...

Sealing Washer for the cylinder block oil jet adaptor on the 2.5L 4-cylinder diesel engine. Seals the jet adaptor against the cylinder block. Fitt...

Brake pipe clip

Bolt & Lockwasher for securing the inlet manifold on the V8 petrol engine. Supplied as a bolt with its matching lockwasher. The imperial 5/16"...

Bolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...

Ball Steel Bearing

Body Mount Spacer Tube forms part of the body-to-chassis mounting assembly, located at a mount point between the body and the chassis frame. It se...

Plain Washer - a flat load-spreading washer used at the body-to-chassis mount fixings. Fitted under the bolt head or nut, it distributes clamping ...

Wheel Stud - Front Drive Shaft Hub is a press-fit threaded stud for the front drive shaft hub assembly. It provides the fastening point that secure...

Crankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...

Locating Dowel for the flywheel-to-crankshaft joint, part of the crankshaft and flywheel assembly. Pressed into the crankshaft rear flange, the do...

Sealing Washer is a copper joint washer used in multiple engine and ancillary applications across the Land Rover range, including as a sealing wash...

Sac Snap Clip

Rear Propeller Shaft assembly for the rear axle driveline. Installed between the transfer gearbox rear output flange and the rear differential inp...

Dial Illumination Bulb - the backlight bulb and bulbholder assembly for the LCD climate control panel, part of the heating and ventilation controls...