Land Rover Discovery Parts

Fuel Tank Sender Unit - Front for the Discovery 3 (2005-2009), providing the float and resistor assembly that measures fuel level and transmits rea...

Fuel Tank Sender Unit for the rear fuel tank. This sender unit mounts directly in the rear fuel tank and measures fuel level via a float and resis...

Crankshaft Trigger Wheel Installer - a service tool for fitting the crankshaft trigger (reluctor) wheel to the crankshaft on the TDV6 engine. It l...

Ball Joint Separator - a heavy-duty scissor-type hand tool that eases tapered ball joints and track rod ends apart without impact, avoiding damage ...

Diff Lock Lever Arm for the LT230 transfer box differential lock linkage assembly. This lever forms part of the mechanical actuation system that e...

Windscreen Wiper

Viscous Fan Coupling - temperature-sensitive drive coupling between the water pump drive and the engine cooling fan. It modulates fan speed with u...

Panhard Rod Bush for the front suspension lateral location assembly. This rubber bush is pressed into the Panhard rod eye and provides the complia...

Screw for securing the engine wiring harness in Rover V8 petrol engine installations. Fastens harness clips and mounting brackets to the engine bl...

Timing Belt for the camshaft drive of the 300 TDi diesel engine, running within the timing belt and tensioner assembly at the front of the engine. ...

Oil Jet for cylinders No.2 and No.4, fitted in the cylinder block of the 2.5L Diesel NA, 2.5L Turbo Diesel, 200TDi and 300TDi engines. This piston...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Differential Pinion Bearing Shim - 0.068 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Clutch Slave Cylinder for the manual transmission clutch release hydraulic circuit. It is fed by the clutch master cylinder and mounts at the gearb...

Circlip - Driveshaft Boot is a retaining circlip used within the driveshaft CV joint boot assembly. The circlip secures components within the CV j...

Idler Pulley for the auxiliary (ancillary) drive belt of the air-conditioning system. The pulley guides and tensions the belt that drives the air-...

Needle Roller Bearing for the R380 manual gearbox. It carries the reverse idler on the layshaft, allowing the gear to rotate with minimal friction ...

Needle Roller Bearing for the manual gearbox mainshaft. The bearing carries a constant-mesh mainshaft gear, letting it spin freely on the mainshaf...

Fuse - 60A - high-current blade fuse for the main electrical protection circuits. Rated at 60 amps, this fuse protects high-draw circuits such as ...

Oil Separator for the crankcase ventilation circuit of the 3.0L V6 Diesel engine. Mounted within the crankcase emission control system, the separa...

Fusible Link - 30A is a high-current protection component located in the engine fuse box. This fusible link protects the engine wiring circuits by...

Window Control Switch for the driver's door, in the double configuration. The switch is mounted in the driver's door armrest and operates the elec...

Idler Pulley for the auxiliary drive belt, 70mm diameter, positioned within the front-end accessory drive system. The pulley guides and stabilises...

Throttle Body Housing Seal seals the rear interface of the throttle body housing where it mates with the adjoining intake ducting, within the engin...

Lock Nut for the front output shaft, used in the transfer box assembly. This nut secures the front output shaft drive flange within the transfer b...

Battery Fixing Stud - Long Straight is a long straight J-bolt used to secure the battery retaining clamp to the battery tray. The stud passes thro...

Track Rod Assembly is the complete steering track rod that links the front wheels across the axle, forming part of the steering linkage. The assem...

Throttle Seal for the intake throttle valve housing. It fits at the joint between the throttle body and the intake, maintaining an airtight connec...

Screw - a fastener used to secure exterior body panels and trim, including body mouldings, front and rear bumper assemblies, radiator grille panels...

Door Latch for the front door, right-hand side, operating within the door lock control assembly. The latch engages the striker on the body aperture...

Transmission Oil Cooler Pipe Assembly, part of the automatic transmission fluid cooling circuit. It routes transmission fluid between the ZF 6HP28...

Exhaust Gas Temperature Sensor monitors exhaust gas temperature within the diesel after-treatment system, mounted in the exhaust line at the cataly...

Crankshaft Oil Seal - 2.0L MPi is the oil seal for the crankshaft on the 2.0L T-Series MPi petrol engine. The T-Series is a 2.0-litre four-cylinde...

Snorkel Head is the 3" ram-air intake head that fits to the top of a raised air intake tube, forming the forward-facing scoop that feeds cool, clea...

Poly Bush Kit - a polyurethane suspension bush set for the chassis and suspension linkages. The kit replaces the original rubber suspension bushes...

Rocker Cover Gasket - Right Hand for the AJ V8 petrol engine. This gasket seals the rocker cover to the right-hand cylinder head, preventing oil fr...

Rocker Cover Gasket - Left Hand for the AJ V8 petrol engine. This gasket seals the rocker cover to the left-hand cylinder head, preventing oil from...

Brake Reservoir Kit for the Girling dual-circuit brake master cylinder. This kit provides the replacement components for the fluid reservoir secti...

Brake Mudshield is the splash shield fitted behind the right-hand rear brake disc. Mounted to the rear hub assembly, it shields the disc and braki...

Rear Brake Mudshield (Left-Hand) is a stamped backing plate that fits behind the rear brake disc within the rear disc brake assembly. It shields t...

Front Shock Absorber Turret: the tubular mounting tower that locates the upper end of the front damper. It bolts to the chassis and provides the t...

Roof Rack Side Rail Gasket for the front roof rack side rail mounting, left-hand upper position. This gasket seats between the front roof rack sid...

Roof Rack Side Rail Gasket for the front roof rack side rail mounting, right-hand upper position. This gasket seats between the front roof rack si...

Roof Rack Side Rail Gasket for the front roof rack side rail mounting, left-hand lower position. This gasket seats between the front roof rack sid...

Roof Rack Side Rail Gasket for the front roof rack side rail mounting, right-hand lower position. This gasket seats between the front roof rack si...

Roof Rack Side Rail Gasket - the rear sealing gasket for the roof rack side rail, part of the roof rack mounting assembly. It sits between the rea...

Roof Rack Side Rail Gasket for the rear roof rack side rail mounting, right-hand side. This gasket seats between the rear roof rack side rail and ...

Sunroof Handle Assembly operates the manually-operated glass sunroof, forming the interface between the occupant and the roof panel's opening mecha...