Land Rover Discovery Parts

Needle Bearing - LT77 5-Speed Gearbox - Mainshaft This needle roller bearing supports the mainshaft gear cluster within the LT77 5-speed manual ge...

Rivet Screw - 6.3 x 22mm for securing panels and trim on Land Rover vehicles. This scrivet-type fastener combines a screw thread with a expanding ...

Centre Plate Gasket for the LT77 5-speed manual gearbox. This gasket seals the joint between the main casing sections of the LT77 gearbox, prevent...

Fuel Filter within the diesel fuel supply assembly. This filter traps particulate contamination in the fuel supply circuit before fuel reaches the...

Air Filter element for the engine air cleaner housing. Seated in the air cleaner housing upstream of the mass air flow sensor and throttle body, t...

Air Filter element for the engine air cleaner assembly. The filter sits inside the air cleaner housing and cleans the intake air before it passes ...

Ignition Switch for vehicles equipped with passive keyless entry and start. It forms part of the keyless ignition and engine-start control, initia...

Transmission Sleeve for the ZF 6HP26 and 6HP28 six-speed automatic transmission. It is fitted within the main control valve body, where it forms th...

Bump Stop Mounting - a weld-on chassis bracket that provides the mounting point for a rear axle bump stop. The bracket is welded to the chassis to...

Fuel Filler Door Seal is the rubber seal fitted around the fuel filler door aperture in the rear body panel. It seals the recess behind the hinged...

Oil Pump for the R380 manual gearbox. Mounted at the rear of the gearbox and driven from the output shaft, the pump circulates gearbox oil to lubr...

Fuel Filler Door Latch secures the fuel tank filler flap in the closed position. The latch holds the filler door flush against the body and releas...

Brake Pad Wear Warning Wire for the rear brake pad wear-indication circuit. The sensor wire is routed into the friction material of the rear brake...

Hex Nut - 7/16 UNF fixing nut. Used on the fuel pipe unions of the 3.5L V8 twin-carburettor petrol engine. Also supplied as part of a service kit.

Drain Plug Washer is the copper sealing washer for the drain plug on the LT77 manual gearbox. It seats between the magnetic drain plug and the gea...

Turbocharger to Intercooler Hose for the 300TDi 2.5L turbocharged diesel engine intercooler circuit. This hose connects the turbocharger compresso...

Swivel Pin Bush - Upper is the upper pivot bush in the front axle swivel housing assembly. It seats in the top of the swivel housing and locates t...

Differential Pinion Bearing Shim - 0.070 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Flanged Hex Bolt, M12 x 70mm. Secures the front wheel hub assembly to the steering knuckle (upright) within the front suspension and hub assembly....

Hex Nut

Bulb and Holder for switch and control panel illumination. The orange-tinted bulb and its integral holder fit into the rear of dashboard switches ...

Stud - Turbo Outlet to Downpipe Flange in the exhaust system of the Td5 2.5L 5-cylinder turbo diesel engine. This stud secures the turbocharger ou...

Thrust Washer is a 1.15mm selective thrust washer for the centre differential of the LT230 transfer box. It sets the end-float of the centre diffe...

Dowel is a precision locating pin that aligns mating components during assembly, setting their position accurately and relieving the securing bolts...

Hex-Head Bolt with Washer, M4 x 14. Fastener used in the front end carrier assembly, securing the front panels, aprons and side members.

Locking Nut for the steering linkage, retaining a track rod end onto the drag link or track rod. Once the joint is set to position, the nut is tigh...

Seat Belt Fixing Kit provides the mounting hardware used to secure a seat belt assembly to the vehicle body anchorage points. The kit supplies the...

Synchromesh Ring for the R380 5-speed manual gearbox, the intermediate ring for 1st to 4th gears. The synchroniser ring matches the speed of the s...

Wiper Blade with Spoiler for the front windscreen wash/wipe system, for left-hand drive applications. The integral aerodynamic spoiler maintains c...

Wheel Cylinder Brake - RH

Rocker Cover Screw - Long for the Rover 3.5L V8 engine. This long 1/4" UNC x 1-5/16" screw secures the rocker cover to the cylinder head on the Ro...

Inlet Valve for the cylinder head valvetrain of the Rover V8 petrol engine (3.5L, 3.9L, 4.0L and 4.6L variants). It seats in the cylinder head inl...

Alternator is the charging source of the engine electrical system. Driven by the accessory drive belt, it converts crankshaft rotation into electri...

Alternator serving the charging circuit of the 2.7L and 3.0L V6 diesel (TDV6) engine. Driven by the accessory drive belt, the alternator converts ...

Flanged Clip Nut is an M6 captive nut retained in a spring-steel clip. The clip pushes onto a panel edge or into a mounting hole to hold the nut c...

Grille is the front-face grille panel for the Discovery 1, fitted to the nose of the vehicle between the headlamps and above the front bumper. Thi...

Front Upper Suspension Arm for the left-hand side, part of the front double-wishbone suspension assembly. The arm forms the upper link between the...

Cylinder Head Bolt for the Rover V8 engine, 7/16" UNC thread. Used to secure the cylinder head to the block on the Rover 3.5L, 3.9L and 4.0L V8 en...

Oil Separator Pipe for the 3.0L V6 diesel engine, forming part of the crankcase emission control (crankcase ventilation) system. It carries blow-b...

Front Window Regulator and Motor - LH is an integrated electric window assembly for the left-hand front door. It combines the regulator mechanism a...

Differential Pinion Bearing Shim - 0.064 in, for use in the Rover 10-spline rear differential. This shim sets the preload on the pinion outer beari...

Trim Clip - push-fit fastener securing exterior body mouldings, front and rear bumper trim and the radiator grille to the body panels. Renews an o...

Wheel Nuts - set of five, sufficient to secure one wheel. The nuts are sized for the MaxXtrac Mach 5 alloy wheel, giving the correct seat and thre...

Gearbox Selector Pad for the LT77 five-speed manual gearbox. Fits the 5th gear selector within the selector and yoke assembly, forming the bearing...

Exhaust Manifold Stud secures the exhaust manifold flange to the cylinder head within the exhaust assembly. This is a double-ended stud, threaded ...

o-ring oil cooler 3,0 TDV6

Latch hood, bonnet, RH and LH, with sensor

Automatic Transmission Shaft is a coupling shaft within the ZF 4-speed automatic gearbox assembly. This shaft transmits drive between internal gea...