Land Rover Discovery Parts

Power Steering Pressure Hose - LHD for the power steering hydraulic circuit. This high-pressure hose connects the power steering pump outlet to th...

Inlet Manifold Seal for the V8 petrol induction system, straight pattern. The seal closes the joint between the underside of the inlet manifold an...

Cyclone Breather Filter for the crankcase ventilation system on the four-cylinder 2.5L diesel engine (naturally aspirated, 200TDi and 300TDi). Mou...

Brake Hose Clip in the brake hydraulic circuit, securing a flexible brake hose to its mounting bracket where the hose crosses from the chassis to a...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Suspension Bush for the rear lower link (bottom link) of the coil-sprung rear suspension. It presses into the link eye, cushioning the pivot mounti...

Rear Upper Shock Absorber Bracket, the upper mounting bracket for the rear damper within the rear suspension. It forms the fixed upper anchorage b...

Shock Absorber Bush for the lower mounting of a suspension damper. The rubber bush seats in the shock absorber's lower mounting eye, locating the ...

Front Hub Lock Washer located within the Front Hub & Driveshaft Assembly, securing the hub bearing retaining nut in position. The lock washer ...

Upper Ball Joint for the front axle steering knuckle (swivel housing) assembly. The knuckle pivots on an upper and a lower ball joint; this upper ...

Felt Washer for the output shaft assemblies of the LT230 transfer box. This washer is fitted at the front and rear output flanges of the LT230, wh...

Bolt - a threaded fastener used within the rear axle and suspension assembly. It secures the rear knuckle and suspension arm mountings, clamping e...

Glow Plug for the 200TDi and 300TDi 2.5-litre direct-injection turbo diesel engines. It forms part of the cold-start pre-heating system. The glow ...

Fitment All TD5 diesel models up to (VIN) 6A999999 All TD5 diesel models All V8 EFi petrol models 2.5L 6 Cyl BMW Diesel /4.0L and 4.6L EFI V8 P...

Exhaust Manifold Gasket for the 4.0L and 4.6L EFi V8 petrol engine. This twin-port gasket seals the exhaust manifold-to-cylinder head joint at two...

Copper Sealing Washer for banjo bolt connections in the engine oil circuit. This copper washer seats against the machined face of a banjo fitting ...

Cylinder Head Bolt securing the cylinder head to the cylinder block and clamping the head gasket joint. It maintains the clamping force that seals...

Drive Belt Tensioner for the 2.5L Td5 5-cylinder turbo diesel engine. The tensioner is listed in the Land Rover parts catalogue in the Td5 drive b...

Fuel Lift Pump Gasket seals the mechanical fuel lift pump to the engine on 2.5L diesel applications, including the 200TDi and 300TDi. Fitted betwe...

Clutch Fork Insert is the nylon insulator that fits over the clutch fork pivot pin inside the bellhousing, cushioning the fork at its fulcrum point...

Cylinder Head Dowel for the Td5 2.5L 5-cylinder turbo diesel engine. The dowel locates between the cylinder block and the cylinder head, aligning ...

Differential Taper Roller Bearing for the axle differential assembly. It supports the differential carrier within the axle casing, carrying the com...

Nyloc Nut - 1/4" UNF - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under ...

Nyloc Nut - M14 - self-locking nut with a nylon insert set into the collar. The nylon insert grips the bolt thread to resist loosening under vibra...

Nut, 1/2" UNF. A threaded fastener used on the early 4-cylinder diesel engine assembly.

Gearbox Mount, right-hand side. Part of the transmission mounting assembly. The mount sits between the gearbox and transfer box casing and the cha...

Oil Pressure Switch threads into the engine block oil gallery and monitors lubrication system pressure. It operates the low oil pressure warning l...

Hub Nut Socket is a 52mm deep impact socket with a 1/2" square drive, used to remove and refit the hub retaining nut on the wheel bearing assembly....

Front Hub Assembly, ABS configuration. Part of the front axle hub and bearing system. The hub locates the front wheel and carries it for rotation ...

Lower Swivel Pin for the front axle swivel housing assembly. The lower swivel pin provides the lower pivot point for the steering knuckle, working...

Anchor Stud providing a threaded fixing point for interior trim panels, door casings, carpet sections, and air intake duct components. This stud a...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Hydraulic Tappet fitted within the V8 petrol engine valve train, where it maintains zero valve clearance automatically. Engine oil pressure fills ...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Pedal Rubber Pad for the foot pedal. The moulded rubber pad slips over the pedal arm to provide a durable, non-slip foot surface. Fitted to manual...

Radius Arm Bush - Rear, Lower - the compliant mount at the lower link of the rear radius arm, between the arm and its chassis bracket. The rear ra...

Wiper Clip A retaining clip within the windscreen wiper assembly that secures the wiper blade to the wiper arm, holding the blade in place on the arm.

Trim Retention Clip for securing door casing and bodyside trim panels. This push-fit clip engages a panel stud on the door inner frame or body str...

Brake Disc Fixing Screw that secures the brake disc to the wheel hub. The screw locates and retains the disc against the hub face during assembly,...

Brake Pad Retention Kit - front brake pad retaining hardware for the disc brake assembly. Secures the front brake pads in the caliper on installat...

Exhaust Mounting Rubber - flexible support that suspends the silencer section of the exhaust system from the vehicle underbody. The moulded rubber...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Water Pump Gasket seals the coolant pump to the engine front cover on the V8 petrol engine. It fits at the pump mounting face, sealing the coolant...

Thermostat for the 2.5L 200TDi diesel engine, operating within the thermostat housing at the top of the cooling circuit. This thermostat opens at ...

Coolant Hose for the water pump circuit on the 3.5L V8 Twin Carb petrol engine. This hose connects the water pump outlet to the coolant pipe, rout...

Fuel Filter with a paper filter element, for carburettor petrol engines. Part of the fuel supply system. The filter is plumbed inline between the ...

Stub axle