Land Rover Discovery Parts

Radiator Core is a replacement copper cooling core for the 300 TDi radiator, supplied as the core only without the top and bottom tanks. It is int...

Filter Kit 3.9 EFI

LED Driving Light - round auxiliary driving light with a 4" (100mm) diameter housing and 50W LED output. Intended for external mounting as a suppl...

Central exhaust pipe Discovery 300TDI Stainless Steel

Front Bumper End Cap finishes the right-hand outer end of the front bumper assembly. The end cap closes off the corner of the bumper where it wrap...

Front Bumper End Cap for the left-hand side, part of the front bumper assembly. Moulded cap that fits over the outer LH end of the front bumper, c...

Rear Bumper End Cap - LH is the left-hand rear bumper corner cap, the moulded end section that finishes the outer corner of the rear bumper where i...

Rear Bumper End Cap - RH is the right-hand rear bumper corner cap, the moulded end section that finishes the outer corner of the rear bumper where ...

Boot Centre Floor Panel is a rear body repair panel forming the centre section of the boot floor within the rear load area structure.It is a struct...

Radius Arm Bush - Rear for the rear radius arm. The bush is pressed into the radius arm eye and forms the compliant joint between the radius arm a...

Clutch Master Cylinder for the clutch hydraulic circuit, installed at the pedal box. The cylinder converts mechanical clutch-pedal movement into h...

Rear Door Wiper Arm for the tailgate wiper system. Mounts to the rear wiper spindle on the tailgate and carries the wiper blade across the rear wi...

Door Lock Actuator Electric actuator in the central door locking system. Mounted within the door, it drives the latch to the locked and unlocked p...

Self-Tapping Screw - a No. 10 x 1/2" self-tapping screw used as a general-purpose fixing. The self-tapping thread cuts its own mating thread as th...

Self-Tapping Screw - a No. 6 x 1/2" imperial self-tapping fixing used as a general-purpose fastener throughout the body and chassis. The self-tapp...

Nutsert - 1/4" UNF is a blind rivet nut (rivnut) with a 1/4" UNF internal thread. A nutsert is installed into a pre-drilled hole in sheet metal or...

Distributor Drive Gear - V8

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

Front Brake Caliper Piston is a 41mm piston that operates in the front brake caliper, part of the braking hydraulic circuit for solid disc brakes. ...

O-Ring sealing the dipstick tube where it enters the cylinder block on the V8 petrol engine. Fitted around the lower end of the dipstick tube, thi...

Water Pump in the engine cooling circuit, for AJ-V8 4.4L and 4.2L Supercharged petrol engines. This pump circulates coolant through the engine blo...

Sump Gasket 2.7 - TDV6

Oil Temperature Sender located in the engine sump, for the 2.7L TDV6 and 3.6L TDV8 diesel engines. This sender monitors engine oil temperature and...

Front Crankshaft Oil Seal seated in the engine front (timing) cover, sealing the crankshaft nose where it exits the crankcase. The seal runs again...

Reservoir bracket

Repeater Side Clear LED Pair

Exhaust Mounting - Rubber is a rubber isolator in the exhaust suspension system, fitted between the exhaust assembly and the vehicle underbody. Th...

Nut - Plastic - 7mm is a captive plastic fastener for trim and body panel fixing. This plastic nut presses into a 7mm hole in the body or trim pan...

Bolt used in the camshaft assembly of the 3.5L V8 petrol engine. Imperial UNF fastener, 7/16" diameter with a shank length of 1 1/8". Supplied as ...

Clutch Slave Cylinder for the manual transmission clutch release hydraulic circuit. It is fed by the clutch master cylinder and mounts at the gearb...

Clutch Release Fork is the pivoting lever in the clutch release mechanism that acts on the release bearing. Operated by the clutch slave cylinder ...

Bar Anti Roll Bush

Brake Caliper Piston for the front hydraulic disc brake assembly. The piston operates within the caliper bore and transmits hydraulic pressure fro...

Camshaft Pulley O-Ring - the seal fitted at the camshaft pulley on the front timing drive. It seals the joint between the camshaft nose and its dr...

Valve Cotter in the cylinder head valvetrain, locking the valve spring retainer to the valve stem. The cotters seat as a pair into the machined gr...

Brake Pedal Rubber Pad for vehicles with automatic transmission. Fitted over the brake pedal arm in the pedal box assembly, this slip-resistant ru...

Bumper Fitting Kit (Rear) supplies the mounting hardware required to fit the companion rear heavy-duty bumper (DA5646) to the vehicle's rear chassi...

Power Steering Hose is the low-pressure return line of the power steering hydraulic circuit, carrying fluid from the steering box back to the reser...

Retainer Clip - a quarter-turn, click-type fastener used to secure bumper trim and adjacent body panels to the vehicle body. The clip is fitted wi...

Body Mount - To Chassis Frame is a rubber isolation mount positioned at one of the body-to-chassis attachment points. The mount cushions the body ...

Torx Flanged Screw - Front Door Latch Assembly for the front door latch mechanism. This Torx-head flanged screw secures the front door latch assem...

Flanged Nut - M12 for use in Land Rover fastener applications. A metric M12 flanged nut with an integrated washer flange that distributes clamping...

Drive Flange Nut - Front secures the front drive flange (driving member) to the wheel hub, as part of the front hub assembly. It retains the drivi...

Clutch Cover - 4.0 V8 is the pressure plate assembly in the clutch system. The clutch cover bolts to the flywheel and clamps the clutch driven pla...

Front Axle Drive Shaft Spacer for the front hub and stub axle assembly. The spacer fits over the front drive shaft and sets the axial position of ...

Oil pump relief valve washer V8

Head Gasket - Metal for the 3.9L V8 EFI engine, sealing the cylinder head to the engine block in the top-end assembly. This multi-layer steel head...

Piston Cooling Oil Jet Relief Valve - part of the engine lubrication system, fitted in the cylinder block oil feed to the piston cooling jets. It r...