Land Rover Discovery Parts

Compression Olive for rigid fuel pipe unions. This 8 mm ferrule seats between the union nut and the fitting body, compressing onto the pipe as the ...

Shock Absorber Turret Bracket is the front suspension turret that caps the coil spring and carries the upper mounting of the front shock absorber. ...

Radius Arm Cup Washer is the dished washer used at the front radius arm mounting, seating against the radius arm bush to spread the clamping load o...

Joint Washer sealing the mounting joint between the cylinder block and the auxiliary unit driven off the engine: the vacuum pump on diesel engines,...

Rocker Cover Gasket for the 2.5L 300TDi diesel engine, sealing the interface between the rocker cover and the cylinder head. Installed at the top ...

Fuel Connector Assembly - Pressure Regulator forms part of the fuel pressure-regulation circuit, providing the mounting and connection interface fo...

Drop Arm Ball Joint Kit for renewing the ball joint that connects the steering box drop arm to the drag link. The joint transmits steering input f...

Wheel Nut for securing an alloy road wheel to the hub. The nut clamps the wheel against the hub face on the wheel stud, maintaining correct seatin...

Drag Link Ball Joint Kit for the steering box drop arm on power-assisted steering boxes. The ball joint forms the articulating connection between ...

Coolant Expansion Tank Cap - pressure cap for the cooling system expansion tank, rated at 15 psi. The cap seals the expansion tank and regulates s...

Differential Pinion Oil Seal for the final drive, with a 4-bolt flange (LR-type, non-Salisbury axle). The single-lip seal sits at the front of the ...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Water Pump Gasket Seals the coolant pump to the engine within the cooling system of the 300 TDi 2.5L diesel engine. It forms a coolant-tight joint...

Rubber Mounting A flexible rubber isolation mount used in the exhaust gas recirculation (EGR) system and air-cleaner assembly. It locates and supp...

Diesel Fuel Filter - replaceable cartridge filter element for the fuel supply circuit on 200 TDi and 300 TDi diesel engines. The element sits in t...

Taper Roller Bearing - Diff Pinion - Outer is the outer pinion bearing in the differential final drive assembly, supporting the pinion shaft where ...

Swivel Shim is a 0.75 mm selective shim from the front axle swivel pin assembly. It is fitted beneath the upper swivel pin retaining plate, where s...

Swivel Pin Housing Shim - 0.13mm (0.005") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

O-Ring for the oil filter adaptor assembly on 4-cylinder petrol and diesel engines up to and including the 300TDi. This O-ring seals the joint bet...

Upper Spring Isolator for the coil spring suspension. This rubber seat sits at the upper end of the coil spring, between the top of the spring and ...

Front Cover Gasket seals the timing cover to the front face of the cylinder block on the V8 petrol engine. It fits between the front cover and the...

Oil Filter for the Td5 2.5L 5-cylinder turbo diesel engine, a cartridge element fitted in the engine oil filtration circuit. This is the short-len...

Injector O-Ring for the 2.5L Td5 5-Cylinder Turbo Diesel fuel injection system. This O-ring seats in the groove on the injector body at the cylind...

Water Pump Seal: sealing ring for the coolant pump (Land Rover description 'Seal-coolant pump'). Used in the Td5 coolant pump installation, also i...

Panhard Rod Bush from the front suspension's lateral location linkage. The Panhard rod controls sideways movement of the axle relative to the body...

Chassis Harness Grommet - black rubber grommet for the chassis wiring harness, 6 x 33.5mm. Fitted where the wiring harness passes through a chassi...

Transmission Handbrake Shoe Set is the friction pair for the drum-type parking brake mounted on the rear output of the transfer box. When the hand...

Brake Pipe Union - a male tube-nut fitting that secures a flared 3/16" (4.75mm) hydraulic pipe end into a female union, T-piece or cylinder port. ...

Crankshaft Position Sensor for the Td5 2.5L 5-cylinder turbo diesel engine management system. The sensor reads the toothed reluctor on the flywheel...

Crankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...

Front axle drive flange designed to connect the drive shaft to the wheel hub assembly. The flange transmits rotational force from the half shaft ...

Amber Side Repeater Lamp, a body-side lamp that repeats the direction indicator signal. The amber lens flashes in time with the front and rear ind...

Wheel Centre Cap - a black alloy-wheel centre cap carrying the Land Rover oval in green and silver. It presses into the centre bore of an alloy wh...

Fuel Filler Latch Clip is a small retaining clip within the fuel filler flap assembly. It holds the spring-loaded latch in position inside the fil...

Coolant Hose - the top radiator hose in the Td5 2.5L 5-cylinder turbo diesel engine cooling system. This hose forms part of the upper coolant circ...

Brake Disc, front, vented. Part of the front braking system. The disc mounts to the front wheel hub and rotates with the wheel; the brake caliper ...

Swivel Pin Housing Thrust Washer for the front axle swivel pin assembly. Installed within the swivel pin housing between the pin head and the hous...

Swivel Pin Housing Shim - 0.25mm (0.010") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin hou...

Swivel Pin Housing Shim - 0.075mm (0.003") for the front axle swivel pin housing assembly. This precision shim is fitted between the swivel pin ho...

O-Ring for the engine cooling system thermostat housing. This sealing ring fits the drain or filler plug on the thermostat housing, providing a le...

Swivel Housing Washer for the swivel pin housing drain plug, part of the front axle swivel assembly. The sealing washer fits beneath the drain plu...

This camshaft sprocket is designed for Land Rover V8 engines, providing precise timing and reliable performance.

Cylinder Block Drain Tap threads into the coolant jacket of the cylinder block, providing a controlled drain point for the engine cooling system. ...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Sump Plug seals the drain aperture at the base of the engine sump, retaining the engine oil and providing the drain point for an oil change. Remov...

Air flow meter TD5 OEM VDO /Delphi

LT230 Transfer Box Bottom Cover Gasket, sealing the main casing bottom cover of the LT230 two-speed transfer box. Fits the main casing bottom cove...

Inlet Manifold Seal sealing the inlet manifold to the cylinder block valley on the V8 petrol engine. This formed seal closes the manifold valley j...