Land Rover Driveshaft & Propshaft Parts

Drive Flange Joint Washer is the sealing washer installed at the joint between the drive flange and the stub axle, preventing differential oil from...

Outer Hub Lock Washer for the front and rear hub assembly on Land Rover solid axles. This lock washer secures the hub bearing retaining nut agains...

Nyloc Nut with a 3/8" UNF thread, used to secure propshaft flange bolts. A nylon insert set into the crown of the nut deforms over the bolt thread...

Hub Oil Seal - Inner for the front and rear wheel hubs, seating around the stub axle. The seal runs on the stub axle to retain hub lubricant and e...

Hub Cap closes the centre of the front hub drive flange, covering the driveshaft coupling bolts within the front axle hub assembly. This is the pl...

Propshaft Bolt - a fastener that secures the propshaft universal-joint flange to the differential drive flange within the driveline. It clamps the...

Transfer Box Output Flange Oil Seal is a radial shaft seal fitted at the output flange of the LT230 transfer box, sealing between the rotating outp...

Propshaft Gaiter with Clips for the front propshaft sliding joint. This rubber gaiter fits over the splined sliding joint (slip yoke) of the front...

Hub Bearing - a tapered roller bearing for the front and rear axle wheel ends. It supports the rotating wheel hub on the stationary stub axle, carr...

Swivel Joint Washer located within the Swivel Pin Housing Assembly, sealing the interface between the swivel housing flange and the axle beam face....

Swivel Housing to Stub Axle Joint Washer for the front axle swivel assembly. This sealing washer fits between the swivel housing and the stub axle...

Oil Seal for the LT230 transfer box input shaft. Part of the transfer box gear train. The seal fits around the rotating input shaft where it enter...

Gasket and Seal Kit for the LT230 transfer box, supplying the gaskets and seals needed to reseal the casing on overhaul. Used when the transfer bo...

Stub Axle Gasket

Nyloc Nut with a 3/8" UNF thread and a 12 mm across-flats hex, in the full-height (thick) form. A nylon insert set into the crown of the nut defor...

Nyloc Nut with an M20 thread, used across suspension and driveline flange fastenings. A nylon insert set into the crown of the nut deforms over th...

Front Hub Nut for the front hub and driveshaft assembly, retaining the wheel hub and bearing assembly on the stub axle. This large-diameter locknu...

Drive flange for the front axle drive shaft hub assembly. This component provides the splined connection between the drive shaft and the wheel hub,...

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Swivel Pin Housing Oil Seal - 9mm seal fitted to the front axle swivel housing. It seals the point where the drive shaft enters the swivel housing...

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Universal Joint for the propeller shaft, of the 82mm cap-to-cap type. The universal (cardan) joint connects two sections of the propshaft, transmi...

Oil seal designed to retain lubricant and prevent contamination at the stub axle interface. The seal fits into the stub axle and forms a barrier b...

Differential Pinion Oil Seal for the axle differential housing. This oil seal fits around the pinion flange where the propshaft coupling connects,...

Circlip for the drive shaft and hub assembly on Land Rover permanent four-wheel drive axles. This circlip locates in a machined groove on the driv...

Differential Carrier Gasket for the Rover-type axle assembly. The gasket seals the differential carrier housing against the axle casing at the cen...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Transfer Box Gear Lever Knob fitted to the LT230 transfer box gear lever in vehicles where the LT230 is paired with the LT77 main gearbox. The lev...

Rubber Sealing Ring for gear selector shafts in the LT76 gearbox and LT95 transfer box. In the LT76 gearbox, two rings are fitted per unit, sealin...

Oil Filler Plug serving as the combined fill and level check point for the swivel pin housing, manual gearbox gearcase, and LT230 transfer box on L...

Universal Joint for the propshaft, transmitting rotational drive between shaft sections while accommodating the angular movement of the driveline. ...

Bolt, M10 x 45 securing the front drive member to the hub. The drive member transmits torque from the axle shaft to the road wheel, and these bolts...

Stub Axle Oil Seal - Inner

Drain Plug for differential casings and LT230 transfer boxes. The tapered plug seals the oil drain, fill, and level holes in differential and axle...

Axle Key Washer for the hub nut locking system in the axle assembly. This tab washer seats beneath the axle hub nut, with tabs that locate into ma...

Swivel Pin Gasket seals the joint between the swivel pin housing and the axle case on the front axle. It sits at the mating face where the swivel ...

Gear Oil - EP80W90 extreme-pressure gear lubricant for manual gearboxes, transfer cases, and axle drives. The EP80W90 grade combines extreme-press...

Hub Outer Oil Seal for the front and rear wheel hub assemblies. Located at the outer end of the hub, it retains the wheel-bearing grease within the...

Oil Seal Retainer for the front axle swivel housing assembly. This retaining plate holds the swivel housing oil seal square against the chrome swiv...

Stub Axle Locking Plate - Mudshield

Front Stub Axle for the front hub and swivel pin housing assembly at the front axle. The stub axle passes through the swivel pin housing and provi...

Front Hub Lock Washer for the front hub and driveshaft assembly. This tabbed washer seats between the hub nut and the hub bearing assembly on the ...

Differential Pinion Oil Seal for the final drive, with a 4-bolt flange (LR-type, non-Salisbury axle). The single-lip seal sits at the front of the ...

Drive Flange for the front hub assembly. The drive flange bolts to the outer face of the hub and engages the splined end of the axle half shaft, t...

Oil Seal - a radial oil seal fitted between the wheel hub and stub axle within the wheel hub and drive shaft assembly. The seal retains lubricant ...

Axle Pinion Gasket for the Salisbury rear axle, sealing the pinion bearing retainer to the differential housing at the propshaft flange end of the ...

LT230 Drain Plug Joint Washer, used across the LT230 transfer box and a range of engine and drivetrain applications. This flat sealing washer seal...