for Discounts / VAT
for Discounts & Correct VAT
Engine mechanical failures rarely arrive without warning. Timing chain rattle on cold start, bearing knock under load, or rising oil consumption are signals that internal components are nearing the end of their service life. Engine internals for Land Rover and Range Rover models are available in this collection, dispatched from our Dutch warehouse network.
Turbochargers, intercooler and boost hoses, air intake parts and inlet manifolds have their own collection: Land Rover Turbo, Intake & Manifolds.
Idler Pulley - timing belt idler for the 200 TDi and 300 TDi engine. Provides a bearing surface on the timing belt path, guiding the toothed belt ...
View full detailsTurbo to exh. manifold gasket 200TDi D1, RRcl.
Viscous Unit
Oil Cooler Hose forms part of the engine oil cooling circuit on the 200TDi. It runs between the oil cooler and the oil pump/filter housing, carryi...
View full detailsFuel Injector for the EFI V8 petrol engine, part of the multi-point electronic fuel injection system. The injector is an electrically-operated sol...
View full detailsFront Cover Gasket for the 2.5L 200TDi diesel engine, the smaller of the front cover gaskets. It seals the joint between the front cover and the c...
View full detailsLock Nut secures the tappet adjuster screw on the rocker shaft, holding the valve clearance once it has been set. Tightened against the rocker arm...
View full detailsOil Feed Pipe - Turbo supplies pressurised engine oil to the turbocharger in the 300 Tdi lubrication circuit. It carries oil from the cylinder blo...
View full detailsGasket
Belt Tensioner for the V8 EFI petrol engine, part of the ancillary (serpentine) drive belt system. The tensioner pulley bears against the auxiliar...
View full detailsRocker Arm, RH for the rocker shaft assembly of the 2.5L 300Tdi turbo diesel engine. Mounted on the rocker shaft, it transfers push rod motion fro...
View full detailsRocker Arm, LH for the rocker shaft assembly of the 2.5L 300Tdi turbo diesel engine. Mounted on the rocker shaft, it transfers push rod motion fro...
View full detailsPolyvee Belt 3.9V8 1253mm
Crankshaft Oil Seal - Rear seals the rear of the crankshaft where it leaves the cylinder block at the flywheel end, retaining oil within the bottom...
View full detailsValve Stem Seal for the Rover V8 engine, part of the cylinder head valve train. The seal fits over the top of the valve stem where it passes throu...
View full detailsOil Drain Pipe Gasket for the turbocharger oil return line on the 300TDi 2.5L turbo diesel engine. It seals the flanged joint where the external o...
View full detailsAlternator is the charging-system generator that supplies current to the battery and vehicle electrical system. Driven from the crankshaft by the ...
View full detailsCamshaft Bearing Set comprises the plain bearing shells that support the camshaft within the cylinder block of the four-cylinder engine. The beari...
View full detailsCamshaft Bearing, the front bearing in which the camshaft front journal runs within the cylinder block. It supports the forward end of the camshaf...
View full detailsCoolant Pipe Adaptor for the engine cooling circuit. It threads into the thermostat housing / cylinder head coolant outlet to provide the connectio...
View full detailsBolt - a 3/8" UNC x 2-3/4" bolt securing the rocker shaft and its oil baffle plate to the cylinder head on the Rover V8 engine. It clamps the rock...
View full detailsExhaust manifold lockplate
Cup Plug - a cup-type core plug (also known as an expansion or welch plug) that seals a casting core hole in the cylinder block or cylinder head. ...
View full detailsPower Steering Pump - the engine-driven pump at the heart of the power steering hydraulic circuit. Belt-driven from the engine, it draws fluid fro...
View full detailsCrankshaft Thrust Washer controls crankshaft end-float - the axial movement of the crankshaft within the block - at the centre main bearing. The w...
View full detailsFlywheel Dowel is a locating dowel that registers the flywheel to the crankshaft rear flange. Pressed into the crankshaft flange, it sets the angu...
View full detailsRocker Cover O-Ring for the VM four-cylinder turbo diesel engine, sealing the rocker (cam) cover to the cylinder head. It maintains the oil-tight ...
View full detailsSeal Washer - Turbocharger Copper sealing washer for the turbocharger oil feed circuit. It seals the banjo union on the turbocharger's oil supply ...
View full detailsWater Pump Gasket for the 2.4L and 2.5L VM diesel engine, sealing the interface between the water pump housing and the engine block. This gasket i...
View full detailsFront Cover Gasket sealing the timing cover to the front face of the cylinder block on the 300TDi 2.5L turbo diesel engine. It forms the oil-tight...
View full detailsCrankshaft Spigot Bush is the clutch pilot bush that presses into the rear face of the crankshaft, between the engine and the clutch. It supports ...
View full detailsCrankshaft Oil Seal - Front - 300TDi
Coolant temperature transducer for the 3.9L V8 EFI petrol engine, part of the engine management sensing circuit. Threads into the coolant passage ...
View full detailsValve Stem Cap is a hardened cap that sits over the tip of the valve stem in the cylinder head valve train. It forms the wear interface between th...
View full detailsCore Plug - Cylinder Block Expansion Port is a pressed-steel sealing plug installed in the outer face of the cylinder block to close the casting ap...
View full detailsPlenum Hose is a moulded hose serving the plenum chamber of the V8 EFI petrol induction system. It forms part of the plenum chamber assembly on th...
View full detailsTiming Belt for the camshaft drive of the 300 TDi diesel engine, running within the timing belt and tensioner assembly at the front of the engine. ...
View full detailsOil Filler Cap Seal fitted between the oil filler cap and the rocker cover opening, sealing the point where the cap closes onto the cam cover. It ...
View full detailsMain Bearing Set for the Rover 3.5-litre V8 petrol engine. These are the replaceable shell bearings that carry the crankshaft in the cylinder block...
View full detailsThrottle Potentiometer Kit adapts the Rover V8 plenum chamber to accept a Colvern throttle position sensor in place of the original two-bolt potent...
View full detailsCrankshaft Oil Seal - Rear for the rear crankshaft oil sealing assembly of the 300 TDi engine. Seated in the rear crankshaft seal housing at the f...
View full detailsAlternator Mounting Screw for the Rover V8 petrol engine alternator assembly. This screw secures the alternator to its mounting bracket on the eng...
View full detailsKit - Timing Belt - 200TDi
Rocker Assembly Aluminium - LH
Starter Motor for V8 petrol engines, operating within the engine electrical starting system. The solenoid-actuated pinion engages the flywheel rin...
View full detailsWater Pump circulates coolant through the engine cooling system. It mounts to the front of the Rover 3.5L V8 engine and is driven by the auxiliary...
View full detailsCylinder Head Gasket Set for the 2.5L 200TDi turbo diesel engine, supplying the top-end gaskets and seals required when the cylinder head is remove...
View full detailsConrod Bearing Kit - 0.010" Undersize for Land Rover four-cylinder petrol and diesel engines. Supplies a complete set of connecting rod big-end bea...
View full detailsEngine Mechanical Parts
The internal components of a Land Rover engine operate under sustained heat, pressure, and mechanical stress. On high-mileage examples, particularly those that have covered 150,000 kilometres or more, the cumulative effect of that stress becomes visible in the form of worn bearings, deterioration of timing belts and associated tensioners, internal timing chain wear, and degraded piston rings.
Understanding which components are most likely to require attention, and why, is the most reliable starting point for any engine repair decision.
Pre-Purchase ChecksEngine internals are unforgiving of mismatched specification. Five checks before placing an order will avoid the most common returns and re-orders we see on this category.
The timing system on Land Rover diesel engines is one of the areas most likely to require intervention on high-kilometre vehicles. The 2.7 TDV6 (276DT), used across the Discovery 3 and Range Rover Sport L320, uses a timing belt. Match timing parts to the engine code and product application before ordering.
On high-kilometre engines, belt service history, tensioner condition, and related timing components require careful attention. Where timing work is being carried out, complete engine-specific kits are strongly recommended.
Where timing belt service has been neglected, risk is more closely associated with belt condition, tensioner failure, or loss of correct timing rather than audible warning.
The 3.0 TDV6 (306DT), used in the Discovery 4 and later Range Rover Sport L320, is a distinct engine from the 2.7 TDV6, so check that timing parts are listed for 306DT application before ordering. Which timing components a job on this engine needs depends on the work being done, so check the product listing for exactly what a kit contains.
The Td5 engine, fitted to the Defender and Discovery 2, uses a timing chain rather than a belt and is generally reliable in this respect. Chain wear and tensioner condition should still be assessed on high-mileage engines, particularly where oil service history is unclear.
The 2.4 TDCi and 2.2 TDCi Puma engines fitted to the Classic Defender are chain-driven for the primary timing system. Timing belt kits visible in some general automotive listings refer to auxiliary drive belts, not the engine timing system, and should not be confused with timing chain components.
The Freelander 2 2.2 TD4 (DW12) uses a primary timing belt to drive the camshafts together with a short internal chain linking the twin camshafts. The belt is a scheduled service item and is the component most commonly required for timing work on this engine. The internal chain and tensioner can develop wear on very high-kilometre examples, leading to top-end noise, though this is secondary to belt condition and service-interval compliance.
Confirm the engine code before ordering timing parts. The 2.7 TDV6 (276DT) and 3.0 TDV6 (306DT) share a family name but use different kits. The engine code sits on a build plate on the cam cover.
Piston ring wear is the primary cause of increasing oil consumption and exhaust smoke on high-kilometre Land Rover engines. Rings lose their ability to seal the combustion chamber and control oil migration from the sump, resulting in blue-grey smoke under acceleration or on the overrun.
Compression testing across all cylinders, combined with a leakdown test, will confirm whether ring wear is the likely cause before committing to an internal rebuild.
Piston ring sets are available for most Land Rover petrol and diesel engines. For diesel applications including the Td5 and the TDV6 and TD4 family, standard and oversize ring sets are available depending on whether the cylinder bore has been re-bored or remains within original specification.
Pistons themselves are typically replaced as part of a full rebuild rather than independently, though ring replacement on a bore that is within tolerance can be a cost-effective partial restoration.
On turbocharged diesel engines, which includes effectively the entire modern Land Rover diesel range, piston and ring condition is closely linked to oil change discipline. Carbon build-up on piston crowns and ring land deposits are significantly more severe on engines that have regularly exceeded oil service intervals. Pairing internal work with a fresh service from the Service Kits collection is the most reliable way to protect new internals.
Modern Land Rover diesel engines rely heavily on variable geometry turbochargers to deliver low-end torque. If turbo lag or underboost codes are present, understanding how variable geometry turbos function helps distinguish a sticky actuator from a complete turbo failure before ordering replacement parts.
Bearing failure is one of the clearest indicators of either oil starvation or long-term lubrication neglect. A deep metallic knock that increases with engine speed often indicates bearing wear, though distinguishing between main and big-end bearings typically requires further inspection and measurement rather than relying on sound alone.
Bearing sets for Land Rover engines are available in standard and undersize specifications. If the crankshaft journal has been reground to restore a worn or damaged surface, undersize bearings matching the grind specification must be fitted. Standard bearings are appropriate for journals that remain within manufacturer tolerances.
Mixing bearing sizes within a single engine is not acceptable. A full set replacement is always the correct approach.
The Td5 engine has a specific oil pressure sensitivity that makes bearing condition directly dependent on oil feed quality. Blocked oil passages, degraded oil pump performance, and extended service intervals all contribute to accelerated bearing wear in this engine. Any bearing replacement on a Td5 should include inspection of the oil pump and oil pick-up strainer as a matter of course.
When ordering Td5 bearings, plan oil pump and pick-up strainer inspection into the same job. Returning the engine to service with new bearings and a restricted oil feed simply repeats the failure.
Any internal engine work involving disassembly of the cylinder head or bottom end requires new gaskets and seals. Head gaskets, sump gaskets, and crankshaft oil seals are commonly required in the course of engine mechanical repair, and a fresh refill of coolant and hoses from the Cooling Parts collection is sensible whenever the head has been off.
Multi-layer steel head gaskets are standard fitment on modern Land Rover diesel engines and should always be replaced with a new gasket rather than reused.
Oil contamination in the intake system on the 2.7 TDV6 is more commonly linked to turbocharger oil seal wear or crankcase breather system issues rather than a conventional gasket failure. This should be assessed during any top-end inspection on these engines. For comprehensive sealing parts, the Corteco Engine Seals collection covers the most common rebuild seal sets.
Buyer ChecklistPatterns observed across our engine-internals orders. None of these are repair instructions. They are buyer-confidence checks that reduce returns and re-orders.
When carrying out engine mechanical work that involves the timing system, it is worth addressing bearing and seal condition at the same time where access permits. The additional parts cost of renewing bearings and rear crankshaft seals is modest relative to the labour involved in disassembly and reassembly.
Returning a vehicle to service with renewed timing components but worn bearings that will require the engine to come apart again within 30,000 kilometres is a poor outcome for both the owner and the workshop.
The same logic applies to piston and ring work. If a cylinder bore inspection shows the bore is within specification but ring wear is evident, ring replacement is worthwhile. If bore wear is present, the decision between a re-bore with oversize pistons and rings, or fitting a reconditioned or replacement short engine, depends on the overall condition of the block and the extent of the wear found.
Model Coverage| Model | Years | Engines covered |
|---|---|---|
| Discovery 4 | 2009 to 2016 | 3.0 TDV6 (306DT), 5.0 V8 |
| Discovery 3 | 2004 to 2009 | 2.7 TDV6 (276DT) |
| Discovery 2 | 1998 to 2004 | Td5, 4.0 V8 |
| Freelander 2 | 2006 to 2014 | 2.2 TD4 (DW12), 2.0 Si4 |
| Freelander 1 | 1997 to 2006 | 2.0 Td4 (BMW M47R), 1.8 petrol |
| Classic Defender | 1990 to 2016 | 200Tdi, 300Tdi, Td5, 2.4 TDCi Puma, 2.2 TDCi Puma |
| Range Rover Sport L320 | 2005 to 2013 | 2.7 TDV6, 3.0 TDV6, 3.6 TDV8, 4.2/4.4 V8 |
| Range Rover L322 | 2002 to 2012 | 2.9 Td6 (BMW M57), 3.6 TDV8, 4.4 V8, 4.2 Supercharged V8 |
| Series 3 | 1971 to 1985 | 2.25 petrol and diesel |
If the engine code or variant is not immediately visible in the product listings, use the fitment search or contact Budget Parts directly to confirm compatibility before ordering.
Technical GuidesService intervals, symptoms of belt and tensioner wear, and what a complete kit should include for the 276DT engine across Discovery 3 and Range Rover Sport L320.
TDV6 timing belt replacement guideHow the 306DT timing drive is laid out, which components are on a scheduled interval, and where the failure points sit on Discovery 4 and later Range Rover Sport L320.
3.0 TDV6 chain and belt service guideHow to identify a warped Td5 exhaust manifold on the Defender or Discovery 2, what causes the failure, and why de-webbing is the durable repair.
Td5 manifold diagnosis and fixThe most consistent early symptom is a rattling or chattering noise on cold start that reduces or disappears once oil pressure builds. This is caused by chain slack before the tensioner pressurises. This noise should be taken seriously: continued use with a stretched chain and worn tensioners significantly increases the risk of timing failure. A persistent rattle that does not clear with oil pressure, or that has become audible at normal operating temperature, indicates the system requires immediate inspection.
Start with the engine code. The 306DT is a distinct engine from the 2.7 TDV6 (276DT), so check that any timing part is listed for 306DT application before ordering. Kit contents also differ between products, so check the product listing for exactly which components are included, and contact Budget Parts with your VIN before ordering if you are unsure.
Yes, in cases where the cylinder bore is within specification and the rest of the engine is in acceptable condition, ring replacement is a viable repair. The engine must be removed and the pistons withdrawn for ring replacement, so this is not a minor job, but it is significantly less involved than a full overhaul. A compression test and bore measurement will confirm whether standard-size rings are appropriate or whether the bore requires attention first. If cylinder wear exceeds the manufacturer's service limit, a re-bore with oversize pistons and rings, or a replacement short engine, is the more appropriate solution.
Bearing failure most commonly results from oil starvation, contaminated oil, or the cumulative effect of extended service intervals. On the Td5, a blocked oil pick-up strainer is a known contributor: oil sludge accumulation restricts flow to the oil pump and reduces main gallery pressure. On turbocharged engines generally, bearing wear accelerates if oil change intervals are extended beyond the manufacturer's recommendation, particularly under hard use or high ambient temperatures. When fitting replacement bearings, inspection of the oil pump output and the condition of oil passages is essential to avoid repeated failure.
In most cases, yes. If an engine is disassembled for bearing work, the additional cost of replacing all bearing sets simultaneously is modest relative to the labour already invested. Unless inspection clearly shows that only one set has failed and all others are within tolerance, a complete bearing replacement is the more prudent approach. Journal diameter measurements must be taken before ordering: if journals have been reground, undersize bearings to the correct specification must be fitted.
The primary cam-drive belt on the DW12 is a scheduled service item. The published service interval for the Freelander 2 2.2 TD4 belt is 240,000 kilometres or 10 years, whichever comes first, with many workshops recommending earlier replacement on hard-use vehicles. The internal chain linking the twin camshafts is not on a scheduled interval but should be inspected on very high-kilometre examples where top-end noise is present. Generic "TD4 timing belt kits" listed online often supply only the cam-drive belt and tensioner; confirm scope before ordering.
Budget Parts supplies parts from established aftermarket manufacturers. Warranty terms vary by product and supplier. For parts intended for engine rebuild applications, check the product listing for specific warranty information or contact Budget Parts before purchase if warranty coverage is a deciding factor.
Updated: 9 October 2026