Land Rover Freelander Parts

Body Panel Locknut for square-hole panel apertures, used in body, interior, and trim panel assemblies. This push-fit captive nut locates into a sq...

Hylomar Hylosil 100 is a neutral-curing RTV silicone sealant for gasketing, sealing and bonding in automotive and engineering applications. It cure...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Differential Pinion Oil Seal with a double sealing lip, for the front and rear differentials. It is press-fitted into the differential housing aro...

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Reverse Lamp Bulb - a 21W 12V single-filament incandescent bulb (type P21W) with a BA15s single-contact bayonet cap, fitted to the rear lamp assemb...

Spring Washer fitted under a nut or bolt head to resist loosening from vibration. An M8 split-ring (single-coil) spring washer. The sprung opening...

Worm-drive Hose Clip with a 32-50 mm clamping range, used to secure a flexible hose to a rigid pipe stub or spigot. Tightening the worm screw draws...

Door Trim Clip for the interior door casing assembly. Fir-tree fastener that secures the door trim casing to the door frame, locating it in the pa...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Injector Sealing Washer seals each fuel injector into the cylinder head within the diesel fuel injection system, for 200 TDi and 300 TDi turbo-dies...

Spire Nut for body-panel fixings - a sprung spring-steel captive nut that clips over a panel edge or into a pierced hole to provide a threaded anch...

HOLDER - BULB - SINGLE POLE - D1/D2/DEF ALL/F1/P38

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Wheel Spanner with a 27 mm socket, a hand tool for removing and refitting wheel nuts. Engages the 27 mm hexagon of the wheel nut to loosen or tigh...

Lock Nut - 7/16" UNF - self-locking nut providing a prevailing-torque fastening. The nut resists loosening under vibration and dynamic load, secur...

Flanged Locking Nut, M10. General-purpose threaded fastener. The integral flange spreads the clamp load over a wider bearing area, removing the ne...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Flange Bolt, M8 x 50 mm - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing ...

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Interior Lamp Bulb is a 239-type festoon bulb rated 12V 5W with a C11 (SV8.5) double-ended cap, used in the interior lighting circuit. The bulb se...

Fuel Tank Locking Ring for the fuel pump and sender unit assembly. This ring secures the fuel pump and sender unit in the top of the fuel tank, pr...

Coolant Temperature Sensor threads into the cylinder head and reports engine coolant temperature to the engine management system and the instrument...

Headlight Bulb – H4 – 12V 60/55W is a dual-filament halogen headlamp bulb for headlamp units that take the standard H4 fitting. It carries both the...

screw M5 x 12

Flange Bolt is an M8 hexagon flange bolt with a 40 mm shank length. The integral flange beneath the head spreads clamping load over a wider bearin...

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Flasher Unit, an electronic direction-indicator flasher relay for towing applications. It regulates the flash rate of the direction indicators and...

Capless Wedge Bulb, 12V 1.2W, for instrument, facia, clock and cigar-lighter illumination. The glass wedge base pushes directly into the panel hol...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Water Pump O-Ring Set provides the sealing rings for the coolant pump, sealing the pump to its mounting face and preventing coolant leakage at the ...

Aluminium Sealing Washer is a soft metal crush washer fitted under a threaded plug or fitting to form a leak-tight joint. When the bolt or plug is...

The Interior Door Card Snap Sac Trim Clips are designed to securely fasten your vehicle's door card and trim pieces. Fitment: all models

Washer Jet Tubing is the flexible hose used within the windscreen washer system, supplied in 1 m lengths. It carries washer fluid from the reservo...

24v dsl long belt

Snap Sac Clip - a push-fit fastener that retains the interior door trim panel (door casing) to the door. The clip locates in the door frame and gr...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Wheel Spanner - 24mm for removing and fitting wheel nuts on Land Rover vehicles. This 24mm spanner is sized for the standard wheel nut used across...

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Dust Cap is the small protective cover that fits over a hydraulic bleed nipple in the braking system. Pushed onto the bleed screw of a brake calip...

Stud - M10 x 25mm, a threaded fastening stud used across a range of Land Rover assemblies. The stud provides a fixed threaded mounting point, allo...

Nyloc Nut with an M8 thread - a nylon-insert locking nut used as a self-locking fastener in threaded assemblies. A nylon collar set into the top o...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...