Land Rover Freelander Parts

Hylomar Hylosil 100 is a neutral-curing RTV silicone sealant for gasketing, sealing and bonding in automotive and engineering applications. It cure...

Stop/Tail Light Bulb - 12V 5/21W (trade reference 380) for rear lamp assemblies. This dual-filament bayonet bulb (BAY15d base) provides 5W tail li...

Hylomar Universal Blue is a non-setting gasket jointing compound for use on gaskets and machined metal joint faces in automotive and engineering ap...

Door Casing Stud for the interior door casing assembly. Locating stud onto which the door casing mounts, retaining the trim panel and holding it i...

Oil Cooler Pipe O-Ring for engine and transmission oil cooling circuits. This O-ring seals pipe fitting and hose connection joints in the oil cool...

Locknut for body and trim panel fixings. It seats into a pre-formed aperture in the panel to provide a captive threaded point for the screws or bo...

Air cleaner element installed in the engine intake air cleaner housing to filter incoming air before it reaches the induction system. The element...

CuNiFer Brake Pipe, 3/16" outer diameter, supplied for the brake hydraulic circuit. The copper-nickel alloy resists corrosion and is soft enough to...

Washer Non-Return Valve for the windscreen wash/wipe system. The valve is fitted into the washer fluid line between the pump and the jets. It perm...

Coolant - Blue RTU pre-mixed engine coolant and antifreeze for older Land Rover models. Ready to use straight from the container - no dilution req...

Bolt, M8 thread x 30mm length. A threaded fastener used to secure components within the vehicle assembly. In the M8 x 30 designation, M8 is the no...

Interior Lamp Bulb is a 239-type festoon bulb rated 12V 5W with a C11 (SV8.5) double-ended cap, used in the interior lighting circuit. The bulb se...

screw M5 x 12

Flanged Screw, M8 x 20mm. A hex-head set screw with an integral flange beneath the head that spreads the clamping load and acts as a built-in washe...

Split Pin Assortment A 280-piece assortment of split pins (cotter pins) in a range of sizes, supplied as a workshop set. Split pins secure castell...

Brake Pipe Clip – Double secures a pair of brake pipes along their routing through the braking hydraulic circuit, retaining both lines against the ...

Brake Cleaner & Degreaser - an acetone-free aerosol solvent cleaner for brake components and general parts cleaning. It removes dirt, grease, ...

Bulb rated 12V 10W with a BA15S bayonet cap. A single-contact bayonet-fitting (BA15S) bulb for 12-volt circuits. The single-contact cap suits sing...

Flanged Head Screw is an M6 x 12mm machine screw with an integral flange beneath the head. The flange spreads clamping load over a wider area and ...

Brake Light Switch, the stop lamp switch mounted at the brake pedal. When the brake pedal is depressed the switch closes the stop lamp circuit to ...

Flange Bolt, M12 - a hexagon-head bolt with an integral flange beneath the head. The flange spreads the clamping load over a wider bearing area an...

Trim Clip is a plastic fastener used to secure interior and exterior trim panels, finishers and wheelarch liners to the body. It pushes into a pre...

Bolt for the brake caliper carrier. Secures the caliper carrier bracket to the hub on disc-brake assemblies, retaining the carrier against braking ...

Spring Washer, M8, a split ring washer used with M8 bolts and nuts to prevent fastener loosening caused by vibration and cyclical loading. The spl...

Bleed Screw for the hydraulic braking system. This bleed screw (bleed nipple) is fitted to brake calipers or wheel cylinders to allow hydraulic fl...

Inertia Switch in the fuel supply and engine electrical circuit. It cuts electrical power to the fuel pump on a sudden impact or severe deceleratio...

Bulb - 501 is a 12V 5W capless wedge-base bulb, designated W5W. The one-piece glass base pushes directly into the holder, with the contact wires f...

Hex Nut - M8 is a standard six-sided metric threaded fastener with an 8 mm nominal thread diameter. It threads onto a matching M8 bolt or stud to ...

Flange Bolt - M6 × 10mm is a metric flanged-head fastener used across a wide range of assembly points on Land Rover vehicles. The integrated flang...

Washer is a plain flat washer used as a general-purpose load-spreading fastening component, with a 6 mm internal diameter and a 15 mm outside diame...

Rear Fog Lamp for the rear lighting circuit, providing the high-intensity red rear light used to make the vehicle conspicuous from behind in poor v...

Pipe and Hose Retaining Clip - Engine is a small-bore clip used to retain pipes and hoses at multiple points across the engine bay and fuel system ...

Engine Coolant, pre-mixed for use in the engine cooling system. It circulates through the radiator, water pump and heater circuit to regulate opera...

Flanged Screw - M6 × 12mm is a metric flanged-head fastener used in body, chassis, and electrical component assembly points on Land Rover vehicles....

Nut An M4 hexagonal plain nut. A general-purpose metric fastener used across a wide range of assemblies. Takes a 7 mm spanner.

Flange Bolt is an M8 x 55 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Flange Bolt is an M8 x 70 mm bolt with an integral flange beneath the head. The flange spreads clamp load across the joint face and acts as a buil...

Bolt - M6 x 80mm is a metric threaded fastener with a 6 mm nominal thread diameter and an 80 mm shank length. It secures bolted joints where an M6...

Indicator Bulb - amber replacement bulb for the exterior indicator lighting circuit. Installs into the indicator lamp housing and provides the amb...

Blade Fuse - 25A for Land Rover electrical systems. This 25A blade fuse protects individual circuits in the vehicle fuse box from overcurrent damage.

Oil Pressure Switch for the V8 petrol engine. The switch monitors oil pressure in the engine lubrication circuit and activates the instrument clus...

Hook & Loop Fastening Strap for securing and bundling loose items within the vehicle interior, cargo area, or workshop. The strap wraps around ...

Wiper Spindle Cap - outer cap for the windscreen wiper spindle, installed at the outer end of the spindle where it passes through the scuttle panel...

Protective Coating Kit - Tintable (4 L) for applying a durable, textured surface coating to body panels, underbody areas, wheel arches, load beds, ...

Crankshaft Bearing (main bearing shell) for the BMW M51D25 2.5L 6-cylinder diesel engine. The main bearing shells sit in the bearing saddles of th...

ABS Sensor Bush is a retaining bush used to locate the wheel speed sensor within its mounting point in the hub or axle assembly. The bush provides...

Fuel pressure regulator BMW Diesel OEM BOSCH

Tow Slider - Adjustable Saddle Type for the Dixon Bate adjustable tow bracket system. This is the vertically sliding saddle piece in the Dixon Bat...